|
|
Número de pieza | CAT3643 | |
Descripción | 3-Channel Ultra High Efficiency LED Driver | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CAT3643 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
No Preview Available ! CAT3643
3-Channel Ultra High
Efficiency LED Driver
Description
The CAT3643 is a high efficiency fractional charge pump that can
drive up to three LEDs programmable by a one wire digital interface.
The inclusion of a 1.33x fractional charge pump mode increases
device efficiency by up to 10% over traditional 1.5x charge pumps
with no added external capacitors.
Low noise input ripple is achieved by operating at a constant
switching frequency which allows the use of small external ceramic
capacitors. The multi−fractional charge pump supports a wide range of
input voltages from 2.4 V to 5.5 V.
The EN/DIM logic input functions as a chip enable and a digital
dimming interface for current setting of all LEDs. Six different current
ratios are available via the interface.
The device is available in the 16−pad TQFN or 12−pad TDFN 3 mm
x 3 mm package with a max height of 0.8 mm.
ON Semiconductor’s 1.33x charge pump switching architecture is
patented.
Features
• High Efficiency 1.33x Charge Pump
• Charge Pump: 1x, 1.33x, 1.5x, 2x
• Drives up to 3 LEDs at 32 mA Each
• 1−wire EZDim LED Current Programming
• Power Efficiency up to 92%
• Low Noise Input Ripple in All Modes
• “Zero” Current Shutdown Mode
• Soft Start and Current Limiting
• Short Circuit Protection
• Thermal Shutdown Protection
• 12−pad TDFN and 16−pad TQFN Packages
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
Applications
• LCD Display Backlight
• Cellular Phones
• Digital Still Cameras
• Handheld Devices
http://onsemi.com
TDFN−12
HV2 SUFFIX
CASE 511AN
TQFN−16
HV3 SUFFIX
CASE 510AD
MARKING DIAGRAMS
HABF
CAT3643HV2−T2
HABG
CAT3643HV2−GT2
JAAE
CAT3643HV3−T2
JAAF
CAT3643HV3−GT2
ORDERING INFORMATION
Device
CAT3643HV2−T2
(Note 1)
Package
TDFN−12
(Pb−Free)
Shipping†
2000 /
Tape & Reel
CAT3643HV2−GT2 TDFN−12
(Note 2)
(Pb−Free)
2000 /
Tape & Reel
CAT3643HV3−T2
(Note 1)
TQFN−16
(Pb−Free)
2000 /
Tape & Reel
CAT3643HV3−GT2 TQFN−16
(Note 2)
(Pb−Free)
2000 /
Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
1. Matte−Tin Plated Finish (RoHS−compliant).
2. NiPdAu Plated Finish (RoHS−compliant).
© Semiconductor Components Industries, LLC, 2014
August, 2014 − Rev. 7
1
Publication Order Number:
CAT3643/D
1 page CAT3643
TYPICAL PERFORMANCE CHARACTERISTICS
(VIN = 3.6 V, IOUT = 60 mA (3 LEDs at 20 mA), CIN = COUT = C1 = C2 = 1 mF, TAMB = 25°C unless otherwise specified.)
100
VF = 3.3 V
90
1x
80
1.33x
1.5x
2x
100
VF = 3.3 V
90 1x
80
1.33x
70 70
60 60
50
40
4.5
4.0 3.5 3.0 2.5
INPUT VOLTAGE (V)
Figure 4. Efficiency vs. Input Voltage
2.0
50
40
4.2
4.0 3.8 3.6 3.4 3.2
INPUT VOLTAGE (V)
Figure 5. Efficiency vs. Li−Ion Voltage
3.0
4
VF = 3.3 V
3
2
1
LEDs Off
0
5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0
INPUT VOLTAGE (V)
Figure 6. Quiescent Current vs. Input Voltage
4
3 2x
1.5x
1.33x
2
1x
1
0
−40
0
40 80 120
TEMPERATURE (°C)
Figure 7. Quiescent Current vs. Temperature
10
8 VF = 3.3 V
6
4
2
0
−2
−4
−6
−8
−10
2.0 2.5 3.0 3.5 4.0 4.5 5.0
INPUT VOLTAGE (V)
Figure 8. LED Current Change vs. Input
Voltage
5.5
10
8 VF = 3.3 V
6
4
2
0
−2
−4
−6
−8
−10
−40 0 40 80
TEMPERATURE (°C)
Figure 9. LED Current Change vs.
Temperature
120
http://onsemi.com
5
5 Page CAT3643
LED Current Selection
At power−up, the initial LED current is set to full scale
(100% brightness) by the external resistor RSET as follows:
LED current + 132
0.6 V
RSET
The EN/DIM pin has two primary functions. One function
enables and disables the device. The other function is LED
current dimming with six different levels by pulsing the
input signal, as shown on Figure 29. On each consecutive
pulse rising edge, the LED current is divided by half to 50%,
then 25%, 12.5%, 6.25% and 3.125% dimming levels.
Pulses faster than the minimum TLO may be ignored and
filtered by the device. Pulses longer than the maximum TLO
may shutdown the device.
The LED driver enters a “zero current” shutdown mode if
EN/DIM is held low for 1.5 ms or more.
TSETUP
THI
TPWRDWN
EN/DIM
TLED
LED
Current
Shutdown
100%
TLO
100%
50%
25% 12.5% 6.25% 3.12%
Figure 29. EN/DIM Digital Dimming Timing Diagram
Table 7. LED CURRENT DIMMING LEVELS
EN/DIM # of Pulses *
EN = High
RSET Gain
132
1st 66
2nd 33
3rd 16.5
4th 8.25
5th 4.125
6th 132
xth Device cycling through gain selection
* The gain is changed on the rising edges of the EN/DIM input.
Shutdown
LED Current
132 x 0.6 V / RSET
66 x 0.6 V / RSET
33 x 0.6 V / RSET
16.5 x 0.6 V / RSET
8.25 x 0.6 V / RSET
4.125 x 0.6 V / RSET
132 x 0.6 V / RSET
GAIN x 0.6 V / RSET
http://onsemi.com
11
11 Page |
Páginas | Total 14 Páginas | |
PDF Descargar | [ Datasheet CAT3643.PDF ] |
Número de pieza | Descripción | Fabricantes |
CAT3643 | 3-Channel Ultra High Efficiency Quad-Mode TM LED Driver | Catalyst Semiconductor |
CAT3643 | 3-Channel Ultra High Efficiency LED Driver | ON Semiconductor |
CAT3644 | 4-Channel Ultra High Efficiency Quad-Mode TM LED Driver | Catalyst Semiconductor |
CAT3644 | 4-Channel Ultra High Efficiency LED Driver | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |