|
|
Número de pieza | ALN1220AT | |
Descripción | Internally Matched LNA Module | |
Fabricantes | ASB | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ALN1220AT (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
No Preview Available ! plerowTM ALN1220AT
Internally Matched LNA Module
Features
· S21 = 19.0 dB @ 940 MHz
= 16.0 dB @ 1500 MHz
· NF of 0.65 dB over Frequency
· Unconditionally Stable
· Single 5V Supply
· High OIP3 @ Low Current
Description
The plerowTM ALN-series is the compactly designed surface-mount
module for the use of the LNA with or without the following gain blocks in
the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS,
PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communi-
cation terminals, CATV and so on. It has an exceptional performance of
low noise figure, high gain, high OIP3, and low bias current. The stability
factor is always kept more than unity over the application band in order
to ensure its unconditionally stable implementation to the application
system environment. The surface-mount module package including the
completed matching circuit and other components necessary just in case
allows very simple and convenient implementation onto the system
board in mass production level.
Specifications (in Production)
Typ. @ T = 25C, Vs = 5 V, Freq. =1220 MHz, Zo.sys = 50 ohm
Parameter
Frequency Range
Gain
Gain Flatness
Noise Figure
Output IP3 (1)
S11 / S22 (2)
Output P1dB
Switching Time (3)
Supply Current
Supply Voltage
Impedance
Max. RF Input Power
Package Type & Size
Unit
MHz
dB
dB
dB
dBm
dB
dBm
sec
mA
V
dBm
mm
Specifications
Min Typ Max
940 1500
16.5 17.5
1.5
1.6
0.65 0.70
27 28
-13 / -8
14 15
40 60
5
50
C.W 29 ~ 31 (before fail)
Surface Mount Type, 10Wx10Lx3.8H
Operating temperature is -40C to +85C.
1) OIP3 is measured with two tones at an output power of +0 dBm / tone separated by 1 MHz.
2) S11/S22 (max) is the worst value within the frequency band.
3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to VS.
1-stage Single Type
More Information
Website: www.asb.co.kr
E-mail: [email protected]
Tel: (82) 42-528-7223
Fax: (82) 42-528-7222
Outline Drawing (Unit: mm)
plerow
ALN1220AT
ASB Inc.
(Top View)
Solder Stencil Area
(Bottom View)
(Side View)
Pin Number
2
5
6
Others
Function
RF In
RF Out
Vs
Ground
Note: 1. The number and size of ground via holes in
a circuit board is critical for thermal RF
grounding considerations.
2. We recommend that the ground via holes be
placed on the bottom of all ground pins for
better RF and thermal performance, as
shown in the drawing at the left side.
Ø 0.4 plated thru holes to ground plane
1/4
(Recommended Footprint)
www.asb.co.kr
June 2009
1 page |
Páginas | Total 4 Páginas | |
PDF Descargar | [ Datasheet ALN1220AT.PDF ] |
Número de pieza | Descripción | Fabricantes |
ALN1220AT | Internally Matched LNA Module | ASB |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |