EM78P247B Datasheet PDF - EMC
| Part Number | EM78P247B | |
| Description | 8-BIT MICRO-CONTROLLER | |
| Manufacturers | EMC | |
| Logo |  |
|
|
There is a preview and EM78P247B download ( pdf file ) link at the bottom of this page. Total 20 Pages | ||
Preview 1 page No Preview Available !
DESCRIPTION
EM78P247/447A/B/C
8-BIT MICRO-CONTROLLER FOR GENERAL PURPOSE PRODUCT
Preliminary
The EM78P247/447A/B/C is an 8-bit microprocessor with low-power, high speed CMOS technology. There
are 4Kx13 bits Electical One Time Programmable Read Only Memory (OTP-ROM) within it. It provides 1
Protect bit and 6 One-time Programmable Option bits to protect the OTP memory code from any external access
as well as the user's options.
The OTP ROM will be incorporated into EM78P247/447A/B/C 8-bit microcontroller instead of it's original
memory. The user's development program can be easily programmed into or verify from this OTP memory by
using EMC OTP PROGRAMMER.
FEATURES
• Operating voltage range: 2.5V~5.5V
• Available in temperature range: 0°C~70°C
• Operating frequency range:
Crystal Type: DC~20MHz at 5V
DC~8MHz at 3V
RC Type:
DC~4MHz at 5V
DC~4MHz at 3V
• 2Kx13 on chip ROM (EM78267A/B/C)
• 4Kx13 on chip ROM (EM78467A/B/C)
• 9 special function registers
• 148x8 general purpose registers (SRAM)
• 3 bi-directional tri-state I/O ports (20 I/O pins for EM78P247/447A) (24 I/O pins for EM78P247/447B)
(22 I/O pins for EM78247/447C)
• 5 level stack for subroutine nesting
• 8-bit real time clock/counter (TCC) with selective signal sources and trigger edges, and with overflow interrupt
• Selectable oscillator options:
XTAL1 type (High frequency)
XTAL2 type (32.768KHz)
RC type
External clock input
• Two oscillator periods per instruction cycle
• Power down mode
• Programmable wake up from sleep circuit on I/O ports
• Programmable free running on-chip watchdog timer
• Ten pull-up and wake-up pins
• Two open-drain pins
• Two R-option pins
• Interrupt function available
• 28 pin DIP, SOIC, SSOP
(EM78P247/447A)
28 pin SOIC
(EM78P247/447C)
* This specification are subject to be changed without notice.
9.30.1997 1
|
| |
 
R3 (Status Register)
EM78P247/447A/B/C
8-BIT MICRO-CONTROLLER FOR GENERAL PURPOSE PRODUCT
Preliminary
76
5 43210
GP PS1 PS0 T P Z DC C
• Bit 0 ( C ) Carry flag
• Bit 1 (DC) Auxiliary carry flag
• Bit 2 (Z) Zero flag. Set to “1” if the result of an arithmetic or logic operation is zero.
• Bit 3 (P) Power down bit. Set to 1 during power on or by a “WDTC” command and reset to 0 by a “SLEP”
command.
• Bit 4 (T) Time-out bit. Set to 1 by the “SLEP” and “WDTC” command, or during power up and reset to 0 by
WDT time-out.
• Bits 5 (PS0) ~ 6 (PS1) Page select bits. PS0~PS1 are used to preselect a program memory page. When executing
a “JMP”, “CALL”, or other instruction which causes the program counter to be changed (e.g. MOV R2,A),
PS0~PS1 are loaded into the 11th and 12th bits of the program counter, selecting one of the available program
memory pages. Note that RET (RETL, RETI) instruction does not change the PS0~PS1 bits. That is, the return
will be always to the page from where the subroutine was called, regardless of the current setting of PS0~PS1
bits.
PS1 PS0
00
01
10
11
Program memory page [Address]
Page 0 [000-3FF]
Page 1 [400-7FF]
Page 2 [800-BFF]
Page 3 [C00-FFF]
• Bit 7 (GP) General read/write bit.
R4 (RAM Select Register)
• Bits 0~5 are used to select the registers (address: 00~3F) in the indirect addressing mode.
• Bits 6~7 determine which bank is activated among the 4 banks.
• If no indirect addressing is used, the RSR can be used as an 8-bit wide general purpose read/write register.
• See the configuration of the data memory in Fig. 4.
R5 (Port 5)
• EM78P247/447A: Only low order 4 bits are used in R5. The high order 4 bits of R5 will be read as “0”.
• EM78P247/447B/C: All 8 bits are used in R5.
R6~R7 (Port 6 ~ Port 7)
• Two 8-bit I/O registers.
* This specification are subject to be changed without notice.
9.30.1997 5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for EM78P247B electronic component. |
| Information | Total 20 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ EM78P247B.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| EM78P247 | The function is 8-BIT MICRO-CONTROLLER. EMC | |
| EM78P247A | The function is 8-BIT MICRO-CONTROLLER. EMC | |
| EM78P247B | The function is 8-BIT MICRO-CONTROLLER. EMC | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
EM78
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||