DataSheet.es    


PDF RFM213W Data sheet ( Hoja de datos )

Número de pieza RFM213W
Descripción low-cost (G)FSK/OOK stand-alone RF receiver
Fabricantes HOPERF 
Logotipo HOPERF Logotipo



Hay una vista previa y un enlace de descarga de RFM213W (archivo pdf) en la parte inferior de esta página.


Total 20 Páginas

No Preview Available ! RFM213W Hoja de datos, Descripción, Manual

RFM213W
Features
„ Embedded EEPROM
y Very Easy Development with RFPDK
y All Features Programmable
„ Frequency Range: 300 to 480 MHz
„ FSK, GFSK and OOK Demodulation
„ Symbol Rate: 0.1 to 100 ksps
„ Sensitivity: -111 dBm @ 9.6 ksps, FSK, 433.92 MHz
„ 3-wire SPI Interface for EEPROM Programming
„ Stand-Alone, No External MCU Control Required
„ Configurable Duty-Cycle Operation Mode
„ Supply Voltage: 1.8 to 3.6 V
„ Low Power Consumption: 4.3 mA @ 433.92 MHz, FSK
„ Low Sleep Current
y 60 nA when Sleep Timer Off
y 440 nA when Sleep Timer On
„ RoHS Compliant
„ Module Size:32*11*5.0mm
Descriptions
The RFM213W is an ultra low power, high performance,
low-cost (G)FSK/OOK stand-alone RF receiver for various
300 to 480 MHz wireless applications. It is part of the
CMOSTEK NextGenRFTM family, which includes a
complete line of transmitters, receivers and transceivers. An
embedded EEPROM allows the frequency, symbol rate and
other features to be programmed into the device using the
CMOSTEK USB Programmer and RFPDK. Alternatively, in
stock products of 433.92 MHz is available for immediate
demands with no need of EEPROM programming. The
RFM213W operates from a supply voltage of 1.8 V to
3.6
V, when it is always on, it consumes only 4.3 mA current
while achieving -111 dBm receiving sensitivity. It consumes
even less power when working in duty-cycle operation
mode via the built-in sleep timer. The device provides
demodulated data, power-on reset output as well as a
system clock output for use by an external microcontroller
or decoder. The RFM213W receiver together with
the
RFM113 transmitter enables an ultra low cost RF link.
RFM213W
Applications
„ Low-Cost Consumer Electronics Applications
„ Home and Building Automation
„ Infrared Receiver Replacements
„ Industrial Monitoring and Controls
„ Remote Automated Meter Reading
„ Remote Lighting Control System
„ Wireless Alarm and Security Systems
„ Remote Keyless Entry (RKE)
 
Email:[email protected]        website://www.hoperf.com                                    Rev 1.0 | Page 1/20

1 page




RFM213W pdf
1.3 Receiver Specifications
Table 4. Receiver Specifications
RFM213W
Parameter
Symbol
Conditions
Min Typ Max
Frequency Range
Symbol Rate
FRF
OOK demodulation
SR
(G)FSK demodulation
300 480
0.1 40
0.1 100
Deviation
Bandwidth-Time Product
FDEV
BT
(G)FSK
1 200
- 0.5 -
Sensitivity
Saturation Input Signal
Level
Working Current
S315-OOK
S433.92-OOK
S315-FSK
S433.92-FSK
315 MHz, SR = 1 ksps
433.92 MHz, SR = 1 ksps
315 MHz, SR = 9.6 ksps, FDEV = 19.2 kHz
433.92 MHz, SR = 9.6 ksps, FDEV = 19.2 kHz
PLVL
IDD-OOK
IDD-FSK
315 MHz, OOK
433.92 MHz, OOK
315 MHz, FSK
433.92 MHz, FSK
-114
-113
-112
-111
10
3.5
3.8
4.0
4.3
Sleep Current
ISLEEP
When sleep timer is on
When sleep timer is off
440
60
Frequency Resolution
Frequency Synthesizer
Settle Time
FRES
TLOCK
From XOSC settled
24.8
150
SR = 1 ksps, ±1 MHz offset, CW interference
52
Blocking Immunity
BI SR = 1 ksps, ±2 MHz offset, CW interference
SR = 1 ksps, ±10 MHz offset, CW
interference
74
75
Image Rejection Ratio
IMR IF = 280 kHz
35
Input 3rd Order Intercept
Point
Two tone test at 1 MHz and 2 MHz offset
IIP3 frequency. Maximum system gain settings
-25
Receiver Bandwidth
BW
50 500
Receiver Start-up Time
TSTART-UP
From power up to receive, in Always Receive
Mode
7.3
Receiver Wake-up Time
TWAKE-UP
From sleep to receive, in Duty-Cycle Receive
Mode
0.61
Unit
MHz
ksps
ksps
kHz
-
dBm
dBm
dBm
dBm
dBm
mA
mA
mA
mA
nA
nA
Hz
us
dB
dB
dB
dB
dBm
kHz
ms
ms
Email:[email protected]        website://www.hoperf.com                                    Rev 1.0 | Page 5/21

5 Page





RFM213W arduino
RFM213W
Table 9. Modulation, Frequency and Symbol Rate
Parameter
Modulation
Frequency
Deviation
Frequency Resolution
(G)FSK Symbol Rate
OOK Symbol Rate
Value
(G)FSK/OOK
300 to 480
1 to 200
24.8
0.1 to 100
0.1 to 40
Unit
-
MHz
kHz
Hz
ksps
ksps
5.3 Embedded EEPROM and RFPDK
The RFPDK is a PC application developed to help the user to configure the CMOSTEK NextGenRFTM products in the most
intuitional way. The user only needs to connect the USB Programmer between the PC and the device, fill in/select the proper
value of each parameter on the RFPDK, and click the “Burn” button to program the configurations into the device. The
configurations of the device will then remain unchanged until the next programming. No external MCU control is required in the
application program.
The RFPDK also allows the user to save the active configuration into a list by clicking on the “List” button, so that the saved
configuration can be directly reloaded from the list in the future. Furthermore, it supports exporting the configuration into a
hexadecimal file by clicking on the “Export” button. This file can be used to burn the same configuration into a large amount of
devices during the mass production. See the figure below for the accessing of the EEPROM.
RFM213W
EEPROM
RFPDK
Interface
CSB
SCL
SDA
CMOSTEK USB
Programmer
Figure 11. Accessing Embedded EEPROM
For more details of the CMOSTEK USB Programmer and the RFPDK, please refer to “AN103 CMT211xA-221xA One-Way RF
Link Development Kits Users Guide”.
5.4 All Configurable Options
Beside the demodulation, frequency and symbol rate, more options can be used to customize the device. The following is a table
of all the configurable options. On the RFPDK, the Basic Mode only contains a few options allowing the user to perform easy and
fast configurations. The Advanced Mode shows all the options that allow the user to customize the device in a deeper level. The
options in “Basic Mode” are a subset of that in the “Advanced Mode”.
Email:[email protected]        website://www.hoperf.com                                    Rev 1.0 | Page 11/21

11 Page







PáginasTotal 20 Páginas
PDF Descargar[ Datasheet RFM213W.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
RFM213Wlow-cost (G)FSK/OOK stand-alone RF receiverHOPERF
HOPERF

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar