|
|
Número de pieza | NCV562 | |
Descripción | Low-Dropout Voltage Regulator | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de NCV562 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
No Preview Available ! NCP562, NCV562, NCP563,
NCV563
80 mA CMOS Low Iq
Low-Dropout Voltage
Regulator
This series of fixed output low−dropout linear regulators are
designed for handheld communication equipment and portable battery
powered applications which require low quiescent. This series
features an ultra−low quiescent current of 2.5 mA. Each device
contains a voltage reference unit, an error amplifier, a PMOS power
transistor, resistors for setting output voltage, current limit, and
temperature limit protection circuits. The NCP562 series provides an
enable pin for ON/OFF control.
The NCP562/NCP563 has been designed to be used with low cost
ceramic capacitors and requires a minimum output capacitor of 0.1 mF.
The device is housed in the micro−miniature SC82−AB surface mount
package. Standard voltage versions are 1.5, 1.8, 2.1, 2.5, 2.7, 2.8, 3.0,
3.3, 3.5 and 5.0 V. Other voltages are available in 100 mV steps.
Features
• Low Quiescent Current of 2.5 mA Typical
• Low Output Voltage Option
• Output Voltage Accuracy of 2.0%
• Temperature Range of −40°C to 85°C
• NCP562 Provides an Enable Pin
• NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
Typical Applications
• Battery Powered Instruments
• Hand−Held Instruments
• Camcorders and Cameras
www.onsemi.com
4
1
SC82−AB (SC70−4)
SQ SUFFIX
CASE 419C
PIN CONNECTIONS &
MARKING DIAGRAMS
GND 1
4 Enable
Vin 2
3 Vout
(NCP562 Top View)
GND 1
4 N/C
Vin 2
3 Vout
(NCP563 Top View)
xxx = Specific Device Code
M = Month Code*
G = Pb−Free Package
(Note: Microdot may be in either location)
*Date Code orientation and/or position and
underbar may vary depending upon manu-
facturing location.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
© Semiconductor Components Industries, LLC, 2015
July, 2015 − Rev. 15
1
Publication Order Number:
NCP562/D
1 page NCP562, NCV562, NCP563, NCV563
6
5
4
3
1
0.5
0
−0.5
−1
0
VOUT = 3.0 V
COUT = 0.1 mF
IOUT = 10 mA
50 100 150 200 250 300 350 400 450 500
t, TIME (ms)
Figure 9. Line Transient Response
60
30
0
−30
1
0.5
0
−0.5
−1
0
IOUT = 1 mA to 30 mA
VIN = 4.0 V
VOUT = 3.0 V
COUT = 0.1 mF
50 100 150 200 250 300 350 400 450 500
t, TIME (ms)
Figure 10. Load Transient Response
60
30
0
−30
400
200
0
−200
−400
0
IOUT = 1 mA to 30 mA
VIN = 4.0 V
COUT = 1.0 mF
VOUT = 3.0 V
100 200 300 400 500 600 700 800 900 1000
t, TIME (ms)
Figure 11. Load Transient Response
3.5
3
2.5
2
1.5
1
0.5
0
0.01
VIN = 5.0 V
VOUT = 3.0 V
IOUT = 50 mA
COUT = 0.1 mF
0.1 1 10 100
f, FREQUENCY (kHz)
Figure 12. Output Voltage Noise
1000
DEFINITIONS
Load Regulation
The change in output voltage for a change in output current
at a constant temperature.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 3.0% below
its nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Maximum Power Dissipation
The maximum total dissipation for which the regulator
will operate within its specifications.
Quiescent Current
The quiescent current is the current which flows through
the ground when the LDO operates without a load on its
output: internal IC operation, bias, etc. When the LDO
becomes loaded, this term is called the Ground current. It is
actually the difference between the input current (measured
through the LDO input pin) and the output current.
Line Regulation
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low dissipation
or by using pulse technique such that the average chip
temperature is not significantly affected.
Line Transient Response
Typical over and undershoot response when input voltage
is excited with a given slope.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 160°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Maximum Package Power Dissipation
The maximum power package dissipation is the power
dissipation level at which the junction temperature reaches its
maximum operating value, i.e. 125°C. Depending on the
ambient power dissipation and thus the maximum available
output current.
www.onsemi.com
5
5 Page |
Páginas | Total 8 Páginas | |
PDF Descargar | [ Datasheet NCV562.PDF ] |
Número de pieza | Descripción | Fabricantes |
NCV562 | Low-Dropout Voltage Regulator | ON Semiconductor |
NCV563 | Low-Dropout Voltage Regulator | ON Semiconductor |
NCV565 | Low Dropout Linear Regulator | ON Semiconductor |
NCV5652 | Dual Power Operational Amplifier | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |