|
|
Teilenummer | DMF-50036ZNBU-FW |
|
Beschreibung | LCD Module | |
Hersteller | OPTREX | |
Logo | ||
Gesamt 17 Seiten First Edition
Approved by
Production Div.
LCD Module Specification
Type No. DMF-50036ZNBU-FW
June 18, 1998
Final Revision
*******
Checked by
Checked by
Prepared by
Quality Assurance Div.
Design Engineering Div.
Production Div.
Table of Contents
1. General Specifications .............................................................................2
2. Electrical Specifications...........................................................................3
3. Optical Specifications ..............................................................................8
4. I/O Terminal...........................................................................................10
5. Test..........................................................................................................12
6. Appearance Standards............................................................................13
7. Code System of Production Lot ..........................................................16
8. Type Number .........................................................................................16
9. Applying Precautions .............................................................................16
10. Handling Precautions .............................................................................17
Rev. Date
Revision History
Page
Comment
DMF-50036ZNBU-FW (AT) No.98-0156
OPTREX CORPORATION
OPTREX
Page 1/17
2.6.Power Supply ON/OFF Sequence
2.6.1.ON Sequence
SIGNAL
VCC
SIGNAL
VADJ
VEE
0≦t
0≦t
LEVEL
VCC
VSS
VCC
VSS
VCC
VSS
VADJ
VEE
2.6.2.OFF Sequence
LEVEL
VCC
VSS
VCC
VSS
VCC
VSS
VADJ
VEE
0≦t
0≦t
SIGNAL
VCC
SIGNAL
VADJ
VEE
Please maintain the above sequence when turning on and off the power supply of the module.
If VEE and/or VADJ is supplied to the module while internal alternate signal for LCD driving
(M) is unstable, DC component will be supplied to the LCD panel. This may cause damage
the LCD module.
DMF-50036ZNBU-FW (AT) No.98-0156
OPTREX CORPORATION
OPTREX
Page 6/17
6 Page 5 . Te s t
No change on display and in operation under the following test condition.
No. Parameter
1 High Temperature Operating
2 Low Temperature Operating
3 High Temperature Storage
4 Low Temperature Storage
5 Damp Proof Test
6 Vibration Test
7 Shock Test
Conditions
40℃±2℃, 96hrs (operation state)
10℃±2℃, 96hrs (operation state)
60℃±2℃, 96hrs
-20℃±2℃, 96hrs
40℃±2℃, 90~95%RH, 96hrs
Total fixed amplitude : 1.5mm
Vibration Frequency : 10~55Hz
One cycle 60 seconds to 3 directions of X, Y, Z for
each 15 minutes
To be measured after dropping from 60cm high on
the concrete surface in packing state.
Notes
3
4
3, 4
3, 4
5
E
B
Dropping method corner dropping
F A corner : once
GD C
Edge dropping
B,C,D edge : once
A
60cm
Face dropping
E,F,G face : once
Concrete Surface
Note 1 : Unless otherwise specified, tests will be conducted under the following condition.
Temperature : 20±5℃
Humidity : 65±5%
Note 2 : Unless otherwise specified, tests will be not conducted under functioning state.
Note 3 : No dew condensation to be observed.
Note 4 : The function test shall be conducted after 4 hours storage at the normal temperature and humidity
after removed from the test chamber.
Note 5 : Vibration test will be conducted to the product itself without putting it in a container.
DMF-50036ZNBU-FW (AT) No.98-0156
OPTREX CORPORATION
OPTREX
Page 12/17
12 Page | ||
Seiten | Gesamt 17 Seiten | |
PDF Download | [ DMF-50036ZNBU-FW Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
DMF-50036ZNBU-FW | LCD Module | OPTREX |
DMF-50036ZNBU-FW-BAN | LCD Module | OPTREX |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |