Datenblatt-pdf.com

TMP86FM29LUG Schematic ( PDF Datasheet ) - Toshiba Semiconductor

Teilenummer TMP86FM29LUG
Beschreibung 8 Bit Microcontroller
Hersteller Toshiba Semiconductor
Logo Toshiba Semiconductor Logo 



Gesamt 30 Seiten
		
TMP86FM29LUG Datasheet, Funktion
8 Bit Microcontroller
TLCS-870/C Series
TMP86FM29LUG






TMP86FM29LUG Datasheet, Funktion
TMP86FM29LUG
Note 6: The recommended operating condition of serial PROM mode in TMP86FM29/FM29L is different from MCU mode. Fore
details, please refer to "Electirical Characteristics" in data sheet of each product.
Condition
After reset release
Changing from STOP mode to NORMAL mode
(at EEPCR<MNPWDW>="1"
Changing from STOP mode to SLOW mode
(at EEPCR<MNPWDW>="1")
Changing from IDLE0/1/2 mode to NORMAL mode
(at EEPCR<MNPWDW>="0")
Changing from SLEEP0/1/2 mode to SLOW mode
(at EEPCR<MNPWDW>="0")
Wait Time‘
210/fc [s]
210/fc [s]
23/fc [s]
210/fc [s]
23/fc [s]
CPU
Halt
Halt
Halt
Halt
Halt
Halt/Operate
Peripherals
Halt
Operate
Operate
Operate
Operate
Note 1: TMP86FM29 (TMP86FM29LUG is excluded.) has a CPU wait function which is a warming up (CPU halt) of CPU
for stabilizing of power supply of Flash memory. Even though TMP86CM29L doesn’t have a Flash memory, the
CPU wait function is inserted to keep the compatibility with Flash product (TMP86FM29). During the CPU wait
period except RESET, CPU is halted but peripheral functions are not halted. Therefore, if the interrupt occurs
during the CPU wait period, the interrupt latch (IL) is set and when IMF has been set to "1", the interrupt service
routine might be executed after CPU wait period . For details, please refer to "Flash Memory" in TMP86FM29 data
sheet. TMP86FM29 (Flash product) should be used as non-volatile product to confirm the software of
TMP86CM29L because of the above reason. And TMP86PM29A/PM29B (OTP product) should be used as non-
volatile product to confirm the software of TMP86C829B/CH29B/CM29B.
Note 2: TMP86FM29LUG does not have warming up of CPU for stabilizing of power supply of Flash memory.
Type-1
(Reference pin =V1)
Type-2
(Reference pin =V1)
VDD
VSS
V3
V2
V1
Reference
Voltage
C1
C
C0
CC
VDD
VSS
V3
C
V2
C
V1
Reference
Voltage
C1
C
C0
Type-3
(Reference pin =V2)
VDD
VSS
V3
C
V2
C
V1
C Reference
Voltage
C1
C
C0
Type-4
(Reference pin =V3)
Type-5
(Reference pin =V3)
VDD
VSS
V3
C
V2
C
V1
C Reference
Voltage
C1
C
C0
VDD
VSS
V3
C
V2
C
V1
C
C1
C
C0
Note 1: TMP86FM29/CM29L/FM29L can't use LCD panel which is driven by 5V because the maximum recommended voltage is
3.6V. Therefore, the voltage level of V3 pin always should be under 3.6V.
Note 2: The operating temperature of TMP86FM29/CM29L/FM29L in Type-1 and Type-2 is -10 °C to 85 °C. For details, please
refer to "LCD Driver" and "Electrical Characteristics" in data sheet.
Note 3: The operating temperature of TMP86C829B/CH29B/CM29B in all Types (Type 1 to 5) is -40 °C to 85 °C. However, there
is a voltage level limitation of V3 and VDD pin in each type. For details, please refer to "LCD Driver" and "Electrical
Characteristics" in data sheet.

6 Page







TMP86FM29LUG pdf, datenblatt
11.9 Status Flag...........................................................................................................................126
11.9.1 Parity Error....................................................................................................................................................................126
11.9.2 Framing Error................................................................................................................................................................126
11.9.3 Overrun Error.................................................................................................................................................................126
11.9.4 Receive Data Buffer Full...............................................................................................................................................127
11.9.5 Transmit Data Buffer Empty.........................................................................................................................................127
11.9.6 Transmit End Flag.........................................................................................................................................................128
12. Synchronous Serial Interface (SIO)
12.1 Configuration.......................................................................................................................129
12.2 Control.................................................................................................................................130
12.3 Serial clock..........................................................................................................................132
12.3.1 Clock source..................................................................................................................................................................132
12.3.1.1 Internal clock
12.3.1.2 External clock
12.3.2 Shift edge.......................................................................................................................................................................133
12.3.2.1 Leading edge
12.3.2.2 Trailing edge
12.4 Number of bits to transfer....................................................................................................133
12.5 Number of words to transfer................................................................................................133
12.6 Transfer Mode.....................................................................................................................134
12.6.1 4-bit and 8-bit transfer modes........................................................................................................................................134
12.6.2 4-bit and 8-bit receive modes.........................................................................................................................................136
12.6.3 8-bit transfer / receive mode..........................................................................................................................................137
13. 10-bit AD Converter (ADC)
13.1 Configuration ......................................................................................................................141
13.2 Register configuration.........................................................................................................142
13.3 Function..............................................................................................................................145
13.3.1
13.3.2
13.3.3
Software Start Mode......................................................................................................................................................145
Repeat Mode..................................................................................................................................................................145
Register Setting.............................................................................................................................................................146
13.4 STOP/SLOW Modes during AD Conversion......................................................................147
13.5 Analog Input Voltage and AD Conversion Result..............................................................148
13.6 Precautions about AD Converter.........................................................................................149
13.6.1
13.6.2
13.6.3
Analog input pin voltage range......................................................................................................................................149
Analog input shared pins...............................................................................................................................................149
Noise Countermeasure...................................................................................................................................................149
14. Key-on Wakeup (KWU)
14.1 Configuration.......................................................................................................................151
14.2 Control.................................................................................................................................151
14.3 Function...............................................................................................................................151
15. LCD Driver
15.1 Configuration.......................................................................................................................153
15.2 Control ................................................................................................................................154
15.2.1 LCD driving methods ...................................................................................................................................................155
iv

12 Page


SeitenGesamt 30 Seiten
PDF Download[ TMP86FM29LUG.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
TMP86FM29LUG8 Bit MicrocontrollerToshiba Semiconductor
Toshiba Semiconductor

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com    |   2020   |  Kontakt  |   Suche