G9130-23 Datasheet PDF - Hamamatsu Corporation
| Part Number | G9130-23 | |
| Description | InGaAs PIN photodiode with preamp | |
| Manufacturers | Hamamatsu Corporation | |
| Logo |  |
|
|
There is a preview and G9130-23 download ( pdf file ) link at the bottom of this page. Total 6 Pages | ||
Preview 1 page No Preview Available !
Global Mixed-mode Technology Inc.
G914
150mA Low-Dropout Linear Regulators
Features
Low, 52µA Ground Current
Guaranteed 150mA Output Current
Dropout Voltage is 100mV @ 50mA Load
Over-Temperature Protection and Short-Circuit
Protection
Adjustable Mode: from 2.5V to 5.5V
Max. Supply Current in Shutdown Mode < 1µA
Low Output Noise is 170 µVRMS
Applications
Notebook Computers
Cellular Phones
PDAs
Digital still Camera and Video Recorders
Hand-Held Devices
Bar Code Scanners
General Description
The G914 is a low supply current, low dropout linear
regulator that comes in a space saving SOT23-5 pack-
age. The supply current at no-load is 52µA. In the
shutdown mode, the maximum supply current is less
than 1µA. Operating voltage range of the G914 is from
2.5V to 5.5V. The over-current protection limit is set at
370mA typical and 150mA minimum. An overtem-
perature protection circuit is built-in in the G914 to
prevent thermal overload. These power saving fea-
tures make the G914 ideal for use in the bat-
tery-powered applications such as notebook com-
puters, cellular phones, and PDA’s.
The G914 is a adjustable output version in a small
SOT 23-5 package.
Ordering Information
PART MARKING VOLTAGE
TEMP.
PIN-
RANGE PACKAGE
G914
14
Adjustable -40°C~ +85°C SOT 23-5
Pin Configuration
IN 1
5 OUT
GND 2
G914
SHDN 3
SOT23-5
4 ADJ
＋
－ BATTERY
CIN
1µF
IN OUT
G914
ADJ
SHDN
GND
OUTPUT
VOLTAGE
R1
R2
COUT
1µF
470pF
Adjustable mode
VOUT=1.250 X ( R2/R1+1)
Ver 0.1 Preliminary
Nov 05, 2001
TEL: 886-3-5788833
http://www.gmt.com.tw
1
|
| |
 
Global Mixed-mode Technology Inc.
G914
Layout Guide
An input capacitance of ≅ 1µF is required between the
G914 input pin and ground (the amount of the capaci-
tance may be increased without limit), This capacitor
must be located a distance of not more than 1cm from
the input and return to a clean analog ground.
Input capacitor can filter out the input voltage spike
caused by the surge current due to the inductive effect
of the package pin and the printed circuit board’s
routing wire. Otherwise, the actual voltage at the IN
pin may exceed the absolute maximum rating.
The output capacitor also must be located a distance
of not more than 1cm from output to a clean analog
ground. Because it can filter out the output spike
caused by the surge current due to the inductive effect
of the package pin and the printed circuit board’s
routing wire. Figure 3 is suggested PCB layout of
G914.
Figure 3. Suggested PCB Layout
*Distance between pin & capacitor must no more than 1cm
Ver 0.1 Preliminary
Nov 05, 2001
TEL: 886-3-5788833
http://www.gmt.com.tw
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for G9130-23 electronic component. |
| Information | Total 6 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ G9130-23.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| G9130-21 | The function is InGaAs PIN photodiode with preamp. Hamamatsu Corporation | |
| G9130-22 | The function is InGaAs PIN photodiode with preamp. Hamamatsu Corporation | |
| G9130-23 | The function is InGaAs PIN photodiode with preamp. Hamamatsu Corporation | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
G913
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||