|
|
PDF GL5ZV43 Data sheet ( Hoja de datos )
| Número de pieza | GL5ZV43 | |
| Descripción | DEVICE SPECIFICATION FOR Light Emitting Diode | |
| Fabricantes | Sharp Electrionic Components | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GL5ZV43 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
PREPARED BY:
Ln
DATE:
/dJfS
ti eds
APPROVED BY:
DATE:
‘7IAh QtV’1,
37 KLA3-E
ELECTRON-X COMPONENTS GROUP
SHARP CORPORATION
SPECIFICATION
1 SPECNo.
ISSUE
PAGE
REPRESENTATIVE
Do996034
Jun/16/99
10 pages
DIVISION:
Opto-Electronic Devices Division
DEVICE SPECIFICATION FOR
Light Emitting Diode
MODEL No.
I GL5ZV43
1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharps consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This products is designed for use in the following application areas;
* OA equipment * Audio visual equipment * Home appliance
* Telecommunication equipment (Terminal) * Measuring equipment
r * Tooling machines * Computers
I
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3), please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportation control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals * Gas leakage sensor breakers * Rescue and security equipment
C * Other safety equipment
I
(3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as ;
* Space equipment * Telecommunication equipment (for trunk lines)
I * Nuclear power control equipment * Medical equipment
1
(4) Please contact and consult witha Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE:
BY:
DATE:
J-i4x-4~/
PRESENTED BY:
72Lazz ,
M.Katoh,
Department General Manager of
Engineering Dept.,IlI
Opto-Electronic Devices Division
Electronic Components Group
SHARP CORPORATION
f?ry
1 page  
Peak Forward Current
vs. Duty Ratio
cTa=250C1
DG996034
MODEL No.
I GL5ZV43
Jun/16/99
PAGE
4/10
I II/Ii//III/I/j/IliIlll[
10
l/100 l/10
1
10
Duty Raito
DR
3-4. Characteristics Diagram(m) (Note 1)
Forward Current vs.Forward
Voltage
(Ta=25%)
0. 1
1 1.2 1.4 1.6 1.6 2 2.2 2.4 2.6
Forward Voltage VF(V)
Relative Luminous Intensity
vs. Frorard Voltage
'a=25'C)
Relative Luminous Intensity
vs. Ambient Temperature
(IF=2OmA)
1oDo
.$-
E
;
2 100
Oh
.f E
A5
.-z
CmI
2ot 10
-60-40-20
Ambient
0 20 40
Temprature
60 80 100120
Ta("C)
0.01 1 I I l(l!/l/
I I lllllli
I I l!illjJ
0. 1 1
10 100
Forward Current IFhA)
(Note 1) Above characteristic data are typical data and not a guarantteed data.
5 Page 
DC996034
MODEL No.
GL5ZV43
Jun/16/!B
PAGE
lo/lo
7 - 3. Soldering Conditions
Solder the lead pins under the following conditions
Type of Soldering
1. Manual soldering
Conditions
295Tk5T, within 3 seconds
2. Wave soldering
2603cr5”C. within 5 seconds
3. Auto soldering
P reheating 70°C to 8O”c, within 30 seconds
Soldering 245”ci:5”c, within 5 seconds
(Note) Avoid dipping resin into soldering bath.
Avoid applying stress to lead pins while they are heated. For example ,
when the LED lamp is moved with the heat applied to the lead pins during
manual soldering or solder repair,disconnection may occur.
7-4 For cleaning
(1) Solvent cleaning : Solvent temperature 45°C or less
Immersion for 3 min or less
(2) Ultrasonic cleaning : The effect to device by-ultrasonic cleaning differs
by cleaning bath size,ultrasonic power
output, cleaning time. PIB size or device mounting
condition etc. Please test it in actual using condition
and confirm that doesn’t occur any defect before starting
the ultrasonic cleaning.
(3) Applicable solvent : Ethyl alcohoLMethyl alcohol, Isopropyl alcohol
In case when the other solvent is used,there are cases that
the packaging resin is eroded. Please use the other solvent
after thorough confirmation is performed in actual using condition.
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet GL5ZV43.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GL5ZV43 | DEVICE SPECIFICATION FOR Light Emitting Diode | Sharp Electrionic Components |
| GL5ZV44 | DEVICE SPECIFICATION FOR Light Emitting Diode | Sharp Electrionic Components |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |