|
|
Número de pieza | ADXL345-EP | |
Descripción | Digital Accelerometer | |
Fabricantes | Analog Devices | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ADXL345-EP (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
No Preview Available ! Enhanced Product
3-Axis, ±2 g/±4 g/±8 g/±16 g
Digital Accelerometer
ADXL345-EP
FEATURES
GENERAL DESCRIPTION
Ultralow power: as low as 23 µA in measurement mode and
0.1 µA in standby mode at VS = 2.5 V (typical)
Power consumption scales automatically with bandwidth
User-selectable resolution from 10 to 13 bits
4 mg/LSB scale factor in all g ranges
32-sample FIFO minimizes host processor load
Single tap, double tap, and free-fall detection
Activity/inactivity monitoring
Supply voltage range: 2.0 V to 3.6 V
I/O voltage range: 1.7 V to VS
SPI (3- and 4-wire) and I2C digital interfaces
Flexible interrupt modes mappable to either interrupt pin
Measurement ranges selectable via serial command
Bandwidth selectable via serial command
10,000 g shock survival
Pb free/RoHS compliant
Small and thin: 3 mm × 5 mm × 1 mm LGA package
ENHANCED PRODUCT FEATURES
Supports defense and aerospace applications (AQEC standard)
Extended industrial temperature range (−55°C to +105°C)
Controlled manufacturing baseline
One assembly/test site
One fabrication site
Enhanced product change notification
Qualification data available on request
APPLICATIONS
Industrial equipment
Aerospace equipment
The ADXL345-EP is an extended performance version of
the ADXL345, which is a small, thin, ultralow power, 3-axis
accelerometer with high resolution (13-bit) measurement at up to
±16 g. Digital output data is formatted as 16-bit twos complement
and is accessible through either a SPI (3- or 4-wire) or I2C digital
interface.
The ADXL345-EP is well suited for extended temperature range
industrial and aerospace equipment. It measures the static
acceleration of gravity in tilt-sensing applications, as well as
dynamic acceleration resulting from motion or shock. Its high
resolution (3.9 mg/LSB) enables measurement of inclination
changes less than 1.0°.
Several special sensing functions are provided. Activity and
inactivity sensing detect the presence or lack of motion by
comparing the acceleration on any axis with user-set thresholds.
Tap sensing detects single and double taps in any direction. Free-
fall sensing detects if the device is falling. These functions can
be mapped individually to either of two interrupt output pins.
An integrated memory management system with a 32-level first in,
first out (FIFO) buffer can be used to store data to minimize host
processor activity and lower overall system power consumption.
Low power modes enable intelligent motion-based power
management with threshold sensing and active acceleration
measurement at extremely low power dissipation.
The ADXL345-EP is supplied in a small, thin, 3 mm × 5 mm ×
1 mm, 14-lead, enhanced plastic package.
FUNCTIONAL BLOCK DIAGRAM
VS VDD I/O
ADXL345-EP
POWER
MANAGEMENT
3-AXIS
SENSOR
SENSE
ELECTRONICS
ADC
DIGITAL
FILTER
CONTROL
AND
INTERRUPT
LOGIC
INT1
INT2
32 LEVEL
FIFO
SERIAL I/O
SDA/SDI/SDIO
SDO/ALT
ADDRESS
SCL/SCLK
GND
CS
Figure 1.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibilityisassumedbyAnalogDevices for itsuse,nor foranyinfringementsofpatentsor other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
1 page Enhanced Product
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Acceleration
Any Axis, Unpowered
Any Axis, Powered
VS
VDD I/O
Digital Pins
All Other Pins
Output Short-Circuit Duration
(Any Pin to Ground)
Temperature Range
Powered
Storage
Rating
10,000 g
10,000 g
−0.3 V to +3.9 V
−0.3 V to +3.9 V
−0.3 V to VDD I/O + 0.3 V or 3.9 V,
whichever is less
−0.3 V to +3.9 V
Indefinite
−55°C to +105°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ADXL345-EP
THERMAL RESISTANCE
Table 3. Package Characteristics
Package Type
θJA
θJC
14-Terminal LGA 150°C/W 85°C/W
ESD CAUTION
Device Weight
30 mg
Rev. B | Page 5 of 12
5 Page Enhanced Product
NOTES
ADXL345-EP
Rev. B | Page 11 of 12
11 Page |
Páginas | Total 12 Páginas | |
PDF Descargar | [ Datasheet ADXL345-EP.PDF ] |
Número de pieza | Descripción | Fabricantes |
ADXL345-EP | Digital Accelerometer | Analog Devices |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |