Datenblatt-pdf.com


CDX-GT484US Schematic ( PDF Datasheet ) - Sony

Teilenummer CDX-GT484US
Beschreibung FM/AM COMPACT DISC PLAYER SERVICE MANUAL
Hersteller Sony
Logo Sony Logo 




Gesamt 30 Seiten
CDX-GT484US Datasheet, Funktion
CDX-GT48UM/GT480U/http://www.xiaoyu163.com
QQSE3RV7IC6E3M1AN5U1AL50
8G9T24840U9S/8GT24894U9S
E Model
CDX-GT480U/GT480US
Ver. 1.0 2008.11
Indian Model
CDX-GT48UM/GT484US
Photo: CDX-GT480US
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
NEW
MG-101Y-188//C
DAX-25A
TEL 13942296513CD player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and utter: Below measurable limit
Tuner section
FM
Tuning range:
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
FM tuning interval: 50 kHz/200 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
AM
Tuning range:
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
AM tuning interval: 9 kHz/10 kHz switchable
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 μV
SPECIFICATIONS
QQ 376315150 892498299USB Player section
Tone controls:
Interface: USB (Full-speed)
Low: ±10 dB at 60 Hz (XPLOD)
Maximum current: 500 mA
Mid: ±10 dB at 1 kHz (XPLOD)
Power amplier section
Outputs: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 52 W × 4 (at 4 ohms)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Power supply voltage: 11 – 16 V
Dimensions: Approx. 178 × 50 × 179 mm
General
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Outputs:
Mounting dimensions:
Audio outputs terminal
Approx. 182 × 53 × 162 mm
(front, sub/rear switchable)
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)
Power antenna (aerial) relay control terminal Mass: Approx. 1.2 kg (2 lb. 11 oz.)
Power amplier control terminal
Supplied accessories:
Inputs:
Card remote commander: RM-X151
Remote controller input terminal
Parts for installation and connections (1 set)
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Design and specications are subject to change
USB signal input terminal
without notice.
www x aoy u163 com. i9-889-365-01 Sony Corporation
FM/AM COMPACT DISC PLAYER
.
2008K04-1
Audio&Video Business Group
© 2008.11
Published by Sony Techno Create Corporation
http://www.xiaoyu163.com






CDX-GT484US Datasheet, Funktion
http://www.xiaoyu163.com
CDX-GT48UM/GT480U/GT480US/GT484US
• CONNECTION
QQ 376315150• Except CDX-GT480US: Argentina model
892498299
*1
*1
FRONT
AUDIO OUT

Left
Izquierdo
Right
Derecho
Left
Izquierdo
TELRight
Derecho
from car antenna (aerial)
desde la antena del automóvil
L
R
REAR/SUB FRONT
AUDIO OUT
REAR / SUB Fuse (10 A)
*AUDIO OUT 2 Fusible (10 A)
Blue/white striped
Con rayas azules y blancas

AMP REM
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
White
Blanco
White/black striped
Con rayas blancas y negras
Gray
Gris
Gray/black striped
Con rayas grises y negras
Green
Verde
Green/black striped
Con rayas verdes y negras
Purple
139422965Morad1o 3
Purple/black striped
Con rayas moradas y negras
REMOTE
IN
*3
Black
Negro
Blue
Azul
Red
Rojo
*1 RCA pin cord (not supplied)
*2 AUDIO OUT can be switched SUB or
REAR. For details, see the supplied
Operating Instructions.
*3 Insert with the cord upwards.
*1 Cable con terminales RCA (no
suministrado)
*2 AUDIO OUT (salida de audio) puede
 cambiarse a SUB o REAR. Para
obtener información, consulte el
manual de instrucciones suministrado.
*3 Insertar con el cable hacia arriba.
ANT REM
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A


QQYellow
Amarillo 376315150 892498299
Connection diagram
 To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow, and red power supply leads.
 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
amplifier
Notes
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
 To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
www .amplifier are connected correctly.
Diagrama de conexión
 A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y
después los cables amarillo y rojo de fuente de alimentación.
 Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
 A AMP REMOTE IN de un amplificador de
potencia opcional
Esta conexión es sólo para amplificadores. La conexión de
cualquier otro sistema puede dañar la unidad.
 Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio
del interruptor de encendido
Notas
Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a
masa negro a una superficie metálica del automóvil.
Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
 Al terminal de alimentación de +12 V que
recibe energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de
alimentación
El cable de control de la antena motorizada (azul) suministrará
cc de +12 V cuando conecte la alimentación del sintonizador.
Si el automóvil dispone de una antena de FM/AM incorporada
en el cristal trasero o lateral, conecte el cable de control de
antena motorizada (azul) o el cable de fuente de alimentación
auxiliar (rojo) al terminal de alimentación del amplificador de
antena existente. Para obtener más información, consulte a su
distribuidor.
Con esta unidad no es posible utilizar una antena motorizada
sin caja de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
Antes de conectar los altavoces, desconecte la alimentación
de la unidad.
Utilice altavoces con una impedancia de 4 a 8 ? con la
capacidad de potencia adecuada para evitar que se dañen.
No conecte los terminales de altavoz al chasis del automóvil,
ni conecte los terminales del altavoz derecho con los del
izquierdo.
No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
Para evitar fallas de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si la unidad
comparte un cable negativo común (–) para los altavoces
xiaoy u163.derechoeizquierdo.
No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados
correctamente, aparecerá “FAILURE” en la pantalla. Si es así,
compruebe la conexión de ambos dispositivos.
com
6
http://www.xiaoyu163.com

6 Page









CDX-GT484US pdf, datenblatt
http://www.xiaoyu163.com
CDX-GT48UM/GT480U/GT480US/GT484US
QQ 376315150 8924982993-7. CHASSIS(OP) ASSY
 chassis (OP) assy
tension spring (KF)
two coil springs (damper) (natural)
slider (R)

coil spring (damper) (green)
lever (D)
gear (LE1)
TEL 13942296513
3-8. CHUCKING ARM SUB ASSY
spring
QQ 376315150 892498299
chucking arm sub assy

Note: Have this portion receive the chassis.
Note: Have this portion receive the chassis.
Note: Be careful not to touch the turn table.
www. xiaoyu163. com
12
http://www.xiaoyu163.com

12 Page





SeitenGesamt 30 Seiten
PDF Download[ CDX-GT484US Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
CDX-GT484USFM/AM COMPACT DISC PLAYER SERVICE MANUALSony
Sony

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche