Datenblatt-pdf.com


GP2W0001 Schematic ( PDF Datasheet ) - Sharp Electrionic Components

Teilenummer GP2W0001
Beschreibung Low Power Infrared Transceiver
Hersteller Sharp Electrionic Components
Logo Sharp Electrionic Components Logo 




Gesamt 15 Seiten
GP2W0001 Datasheet, Funktion
IrDA Data Sheet
GP2W0001YP
115 kbps Transceiver
FEATURES
• Built-in Photodiode
• Operating voltage 2.7 V to 5.5 V
• In circuit design, allow for the degradation of light
emitting diode output that results from long continu-
ous operation (50% degradation/5 years).
• This product shall not contain the following materi-
als, and these materials shall not be used in the pro-
duction process for this product.
– CFCs
– Halon
– Carbon Tetrachloride
– 1.1.1. Trichloroethane (Methylchloroform)
– Specific brominated flame retardants such as the
PBBOs and PBBs are not used in this device.
INTRODUCTION
This specification applies to the outline and charac-
teristics of IrDA 1.2 type (data rate 2.4 kbps to
115.2 kbps, low power option compliant) optical data
communication transceiver.
NOTES
• Caution should be taken to prevent the detector sur-
face from being smeared with dust or dirt, or from
being touched, as it may cause faulty operation.
• Cleaning conditions:
– Solvent cleaning: Solvent temperature 45°C or
less. Immersion for 3 minutes or less.
– Ultrasonic cleaning: The effect of ultrasonic
cleaning on the device differs by cleaning bath
size, ultrasonic power output, cleaning time, PCB
size or device mounting condition, etc. Test the
device under actual conditions and confirm that
ultrasonic cleaning does not cause any immedi-
ate or potential defects.
– Cleaning solvent: The cleaning shall be carried
out with ethyl alcohol, methyl alcohol, or isopropyl
alcohol.
• In order to prevent electrostatic damage to the inte-
grated circuit, handle this device in a static-free envi-
ronment and workstation.
• External force applied to the device after mounting can
cause mounting defects such as the terminal coming
off. Be careful when handling the device and prevent
objects from touching the device after mounting.
• Refer to the ‘Precautions for Soldering’ section.
• When the system (program) is designed, the turn
around time from transmit to receive should be
designed by considering 0.5 ms or more that is spec-
ified by IrDA. This turn around time means the time
that this device temporarily does not detect the
incoming signal, since the transmitted light from the
transmitter side reaches the detector side of the
same transceiver.
• Consider that 20 ms or more (at TA = 25°C, no input
signal) is necessary to return from shut-down mode
to ready operation mode. In addition, thoroughly
confirm the operation in the actual application.
• When there is considerable external stray light or a
light source is located near the transceiver, or the
detector face receives considerable external stray
light, a pulse other than the desired signal output may
be generated as noise on the output terminal of the
transceiver. Consider the layout and structure in your
design to minimize disturbing light on the detector face.
• When the sensor is adopted in an IR communication
system, it should be used according to the signal
method specified by ‘Serial Infrared Physical Layer
Link Specification’ published by the Infrared Data
Association. Faulty operation may occur if a signal
method other than that specified is used.
1 23 456
LEDA TXD SD RXD GND VCC
R2
RL
CX2
CX1
R1
TX SD RXD
VCC
COMPONENTS RECOMMENDED VALUES
CX1 47 µF/6.3 V (NOTE)
CX2 1500 pF/25 V
R1 47 ±5%, 1/10 W (NOTE)
R2
RL
(STANDARD)
RL
(LOW POWER)
1 k±5%, 1/10 W
2.2 ±5%, 1/2 W
(VCC = 3.0 V, IE = 40 mW/sr)
33 ±1%, 1/8 W
(VCC = 3.0 V, IE = 3.6 mW/Sr)
NOTE: Choose the most suitable CX1 and R1 according to
the noise level and noise frequency of power supply.
GP2W0001YP-1
Figure 1. Recommended External Circuit
IrDA Data Sheet
1






GP2W0001 Datasheet, Funktion
GP2W0001YP
115 kbps Transceiver
Electrical Characteristics
TA = -25°C, VCC = 5 V unless otherwise specified
PARAMETER
SYMBOL
Current consumption at no input signal
Current consumption at shut-down mode
High level output voltage
Low level output voltage
Low level pulse width
ICC1
ICC2
ICC1-S
ICC2-S
VOH1
VOH2
VOL1
VOL2
tw
Rise time
Fall time
tr
tf
Maximum reception distance
L
Radiant intensity
Peak emission wavelength
IE
λp
MIN.
4.5
2.5
0.8
1
40
850
NOTES:
1. VCC = 5 V, no input signal, output terminal open, VIHSD = VCC -0.6 V.
2. VCC = 3 V, no input signal, output terminal open, VIHSD = VCC -0.6 V.
3. VCC = 5 V, SD terminal open.
4. VCC = 3 V, SD terminal open.
5. VCC = 5 V.
6. VCC = 3 V.
7. VCC = 5 V, IOL = 400 µA.
8. VCC = 3 V, IOL = 400 µA. See Figures 6, 7, and 8.
9. BR = 115.2 kbps. See Figures 6, 7, and 8.
10. VOH, VOL, tw, tr, tf shall be satisfied at φ ≤ 15°. See Figures 6, 7, and 8.
11.BR = 115.2 kbps, φ ≤ 15°, VCC = 3 V, RL = 2.2 ,
VINTX = 2.7 V, R2 = 1 k±5%, CX2 = 1,500 pF. See Figures 9, 10, and 11.
TYP.
1.0
0.7
0.5
0.3
870
MAX.
1.4
1.0
1.0
1.0
0.6
0.6
8.0
1.2
0.2
350
900
UNIT
mA
mA
µA
µA
V
V
V
V
µs
µs
µs
m
mW/Sr
nm
NOTES
1
2
3
4
5
6
7
8
9
9
9
10
11
11
T1
T2
T1
RADIATION
INTENSITY OF
TRANSMITTER
40 mW/Sr
NOTE: At BR = 2.4 kbps: T1 = 416.7 µs, T2 = 78.1 µs
At BR = 115.2 kbps: T1 = 8.68 µs, T2 = 1.63 µs
GP2W0001YP-6
Figure 6. Input Signal Waveform (Detector Side)
tF
90%
tR
VOH
50%
10%
tW
VOL
GP2W0001YP-7
Figure 7. Output Waveform (Detector Side)
6 IrDA Data Sheet

6 Page









GP2W0001 pdf, datenblatt
GP2W0001YP
21 ±0.8
13 ±0.2
2 ±0.5
115 kbps Transceiver
22.4 MAX.
NOTE: Dimensions are in mm.
330 ±2
17.5 ±0.5
Figure 15. Reel Structure and Dimensions
GP2W0001YP-15
PULL-OUT DIRECTION
LENS
SIDE
Figure 16. Direction of Product Insertion
GP2W0001YP-16
12 IrDA Data Sheet

12 Page





SeitenGesamt 15 Seiten
PDF Download[ GP2W0001 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
GP2W0001IrDA Data Sheet 115 kbps TransceiverSharp Electrionic Components
Sharp Electrionic Components
GP2W0001Low Power Infrared TransceiverSharp Electrionic Components
Sharp Electrionic Components
GP2W0001YPIrDA Data Sheet 115 kbps TransceiverSharp Electrionic Components
Sharp Electrionic Components
GP2W0001YPLow Power Infrared TransceiverSharp Electrionic Components
Sharp Electrionic Components
GP2W0002YPLow Power Infrared TransceiverSharp Electrionic Components
Sharp Electrionic Components

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche