|
|
Número de pieza | AFEM-7780 | |
Descripción | 4x7 Front End Module | |
Fabricantes | AVAGO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de AFEM-7780 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
No Preview Available ! AFEM-7780
UMTS2100 4x7 Front-end Module (FEM)
Data Sheet
Description
The AFEM-7780 is a fully matched WCDMA Band1 Frond-
End Module (FEM) featuring the integration of Avago
Technologies’ power amplifier and FBAR.
The AFEM-7780 offers extended talk time and excellent
linearity by using CoolPAM technology, which enhances
efficiencies in low and medium power mode. Idle current
is as low as 11mA.
The FBAR (Film Bulk Acoustic Resonator) based duplexer
provides low insertion loss and outstanding isolation,
which improves efficiency and RX sensitivity.
By using CoolPAM and FBAR technologies, AFEM-7780
shows best performance with smaller footprint.
Feature
• Excellent linearity
• Operating Frequency:
Tx: 1920~1980 MHz
Rx: 2110~2170 MHz
• 24.5 dBm Linear Output Power (HSDPA)
• Very low quiescence current in low power mode
• High isolation (Low Tx leakage at Rx port)
• HSDPA capable
• 50 ohm input and output matching
• 20-pin surface mounting package
• 4. 0 x 7.0 x 1.1(typ) mm SMT Package
Component Image
Block Diagram
Vcc1(16)
Applications
• WCDMA handset (HSDPA)
Ordering Information
Part Number
AFEM-7780-TR1
Number of Devices
1000
AFEM-7780-BLK 100
Container
178mm (7”)
Tape/Reel
Bulk
Vcc2(15)
)
RX(13)
RFIN
(18)
Input
Match
DA
Inter
Stage
Match
PA
Output
Match
Bias Circuit & Control Logic
Switch
Vmode1
(20)
Vmode0
(19)
Ven
(1)
CPL
(5)
ANT
(10)
1 page Footprint
0.5
17 16 15 14 13 12
y 0.5 18
➀➃
11
19
4.0
➂ Top View 10
0.9
20
1
0.9
0.9
2
➄
➁
3 45
➅➆
67
0.9
7.0
x
9
8
➇
0.1
x
➀ 2.01
➁ 2.26
➂ 3.10
➃ 3.53
Notes :
1. Dimensions in millimeters
2. All GND pins are merged into center ground
3. Radius of non-ground circle is 0.52mm
4. Center position of non-ground circle
y
3.08 ➄
0.90 ➅
2.46 ➆
3.13 ➇
xy
3.92 1.39
5.19 0.83
5.79 0.85
6.70 0.30
Pin Description
Pin # Name
1 Ven
2 GND
3 GND
4 GND
5 CPL
6 GND
7 GND
8 GND
9 GND
10 ANT
Description
Module on/off control
Ground
Ground
Ground
TX Power Coupling Output
Ground
Ground
Ground
Ground
Antenna
Pin # Name Description
11 GND Ground
12 GND Ground
13 RX
DPX RX output
14 GND Ground
15
VCC2
DC Supply Voltage
16
VCC1
DC Supply Voltage
17 GND Ground
18 RFIN TX RF Input
19 Vmode0 Mode Control Voltage
20 Vmode1 Mode Control Voltage
5 Page Handling and Storage
ESD (Electrostatic Discharge)
Electrostatic discharge occurs naturally in the environ-
ment. With the increase in voltage potential, the outlet of
neutralization or discharge will be sought. If the acquired
discharge route is through a semiconductor device, de-
structive damage will result.
ESD countermeasure methods should be developed and
used to control potential ESD damage during handling in
a factory environment at each manufacturing site.
MSL (Moisture Sensitivity Level)
Plastic encapsulated surface mount package is sensitive to
damage induced by absorbed moisture and temperature.
Avago Technologies follows JEDEC Standard J-STD 020B.
Each component and package type is classified for
moisture sensitivity by soaking a known dry package at
various temperatures and relative humidity, and times. Af-
ter soak, the components are subjected to three consecu-
tive simulated reflows.
The out of bag exposure time maximum limits are de-
termined by the classification test describe below which
corresponds to a MSL classification level 6 to 1 according
to the JEDEC standard IPC/JEDEC J-STD-020B and J-STD-
033.
AFEM-7780 is MSL3. Thus, according to the J-STD-033 p.11
the maximum Manufacturers Exposure Time (MET) for this
part is 168 hours. After this time period, the part would
need to be removed from the reel, de-taped and then
re-baked. MSL classification reflow temperature for the
AFEM-7780 is targeted at 260°C +0/-5°C. Figure and table
on following page shows typical SMT profile for maximum
temperature of 260 +0/-5°C.
Moisture Classification Level and Floor Life
MSL Level
1
2
2a
3
4
5
5a
6
Floor Life (out of bag) at factory ambient =< 30°C/60% RH or as stated
Unlimited at =< 30°C/85% RH
1 year
4 weeks
168 hours
72 hours
48 hours
24 hours
Mandatory bake before use. After bake, must be reflowed within the time limit specified on the label
Note :
1. The MSL Level is marked on the MSL Label on each shipping bag.
11
11 Page |
Páginas | Total 15 Páginas | |
PDF Descargar | [ Datasheet AFEM-7780.PDF ] |
Número de pieza | Descripción | Fabricantes |
AFEM-7780 | 4x7 Front End Module | AVAGO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |