Datenblatt-pdf.com


DLC1500AMG-T-1 Schematic ( PDF Datasheet ) - DLC Display

Teilenummer DLC1500AMG-T-1
Beschreibung TFT LCD Panel
Hersteller DLC Display
Logo DLC Display Logo 




Gesamt 19 Seiten
DLC1500AMG-T-1 Datasheet, Funktion
DLC Display Co., Limited
德爾西顯示器有限公司
MODEL No: DLC1500AMG-T-1
TEL: 86-755-86029824
FAX: 86-755-86029827
WEB: www.dlcdisplay.com






DLC1500AMG-T-1 Datasheet, Funktion
Module Name: DLC1500AMG-T-1 Ver1.0
5.4 Connection between receiver and transmitter for LVDS
Note1: The lowest bit (RA0, GA0, BA0, RB0, GB0, BB0), the most upper bit (RA7, GA7, BA7, RB7, GB7,
BB7)
Note2: Connecting cable between LCD panel’s connector and transmitter should use 100Ω twisted line.
Note3: If only Hsync and Vsync, the product don’t work. Make sure DE signal has been input.
http://www.dlcdisplay.com
Page 6 of 19

6 Page









DLC1500AMG-T-1 pdf, datenblatt
should be added.
Module Name: DLC1500AMG-T-1 Ver1.0
Note1: Display signals (D0+/-, D1+/-, D2+/-, D3+/- and CK+/-) must be “0” voltage, exclude the VALID period
(See above sequence diagram). If these signals are higher than 0.3 V, the internal circuit is damaged.
If some of display signals of this product are cut while this product is working, even if the signal input to
it once again, it might not work normally. If customer stops the display signals, they should cut VDD.
Note2: When VDD is on, it should be set above 4.0V.
Note3: The backlight power supply voltage should be inputted within the valid period of display and function
signals, in order to avoid unstable data display.
8.4.2 Power supply voltage ripple
When the power supply is designed, the next form can give the reference. If the voltage ripple is over the
value in next form, the noise should be seen in display area.
Ripple (Measured at input terminal of power supply)
Parameter
VCC (3.3V to drive the panel)
Ripple voltage
≤ 200mVP-P (including spike noise)
8.4.3 Fuse
Parameter
VCC
Fuse
Type
Supplier
FCC16152ABTP KAMAYA
Rating
1.5 A
36 V
Fusing
current
--
Remark
Note
Note: There are different power supply systems from the power input terminal. The power supply capacity
should be less than the fusing current. If the power supply capacity is above the fusing current, the
fuse may blow in a short time, and then nasty smell, smoking and so on may occur.
http://www.dlcdisplay.com
Page 12 of 19

12 Page





SeitenGesamt 19 Seiten
PDF Download[ DLC1500AMG-T-1 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
DLC1500AMG-T-1TFT LCD PanelDLC Display
DLC Display

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche