|
|
|
GX-F8A-P Schematic ( PDF Datasheet ) - Omron
| Teilenummer | GX-F8A-P |
|
| Beschreibung | Rectangular-shaped Inductive Proximity Sensor | |
| Hersteller | Omron | |
| Logo |  |
|
Gesamt 16 Seiten 
761
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
PLC /
TERMINALS
HUMAN MACHINE
INTERFACES
ENERGY CONSUMPTION
VISUALIZATION
COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifier-
separated
GX-F/H
GXL
GL
GX-U/GX-FU/
GX-N
GX
Rectangular-shaped Inductive Proximity Sensor Amplifier Built-in
GX-F/H SERIES
■■General terms and conditions............ F-17
■■Related Information
Glossary of terms........................ P.1386~
■■Sensor selection guide.................. P.757~
■■General precautions...................... P.1405
Conforming to
EMC Directive
pSaUnNaXswoenbiscit-eelehctttrpic:/-/wwowrwks.s.nuentx/s.cuonmx
PNP output Oil resistant Different freq.
type available
type available
Industry No. 1* in stable sensing * Based on research conducted by Panasonic Electric Works SUNX
as of August 2010 among equivalent rectangular inductive sensors.
Can be installed with ample space
This sensor has the longest stable sensing range among the same level of rectangular inductive proximity sensors in
the industry. It is easy to install the sensor.
Maximum operation distance
Stable sensing range
Type
Maximum
operation
distance
Stable sensing range
GX-F/H
series
Previous model
GX-F/H
series
GX-□6
GX-□8
1.6 mm 0.063 in
2.5 mm 0.098 in
0 to 1.3 mm 0.051 in
0 to 2.1 mm 0.083 in
0 to 1.2 mm 0.047 in
0 to 1.8 mm 0.709 in
GX-□12
4.0 mm 0.157 in 0 to 3.3 mm 0.130 in 0 to 3.0 mm 0.118 in
Previous
model
GX-□15
Long sensing
range
5.0 mm 0.197 in
8.0 mm 0.315 in
0 to 4.2 mm 0.165 in
0 to 6.7 mm 0.264 in
0 to 4.0 mm 0.157 in
0 to 6.4 mm 0.252 in
* With standard sensing object
Variation at the maximum operation distance is within ±8 % Temperature characteristics vary within ±8 %
Thorough adjustment and control of sensing sensitivity
greatly reduces individual sensor differences and
variations.
The work of adjusting sensor positions when using
multiple sensors and when sensors have been replaced
is much easier.
Example: GX-□8
0.4 mm 0.016 in or less
Operation distance variation: 0.4 mm 0.016 in or less*
60%
less
Standard
sensing object
1.0 mm 0.039 in or less
Maximum operation distance: 2.5 mm 0.098 in ± 8 %
(2.3 to 2.7 mm 0.091 to 0.106 in)
Operation distance variation: 1.0 mm 0.039 in or less
For the
GX-□8
Standard
sensing
object
Image
Maximum operation distance: 2.5 mm 0.098 in ± 20 %
(2.0 to 3.0 mm 0.079 to 0.118 in)
* Not including temperature characteristics.
Previous
model
Components such as the sensor coil and core and
product design have been totally revised to provide
excellent temperature characteristics.
Stable sensing can be obtained regardless of the time of
day or the yearly season.
16.0
14.0
12.0
10.0
8.0
6.0
4.0
2.0
0.0
–2.0 –20
–4
–10
14
23 °C
73 °F
GX-F/H series
Previous models
Sensing range within temperatures
of –25 to +70 °C
(–13 to +158 °F) are within
±8 % of the range at +23 °C (+73 °F)
( )Previous models:
within
+15
–10
%
0 10 20 30 40 50 60 70
32 50 68 86 104 122 140 158
Ambient temperature [°C °F]
* Typical
 
GX-F/HRectangular-shaped Inductive Proximity Sensor
SERIES
766
SPECIFICATIONS
FIBER
SENSORS
GX-6 type
Type
Front sensing
Item Top sensing
Max. operation distance (Note 3)
Stable sensing range (Note 3)
Standard sensing object
Hysteresis
Repeatability
Supply voltage
Current consumption
GX-F6A(I)
GX-H6A(I)
NPN output
PNP output
GX-F6B(I)
GX-F6A(I)-P
GX-F6B(I)-P
GX-H6B(I)
GX-H6A(I)-P
GX-H6B(I)-P
1.6 mm 0.063 in ± 8 %
0 to 1.3 mm 0 to 0.051 in
Iron sheet 12 × 12 × t 1 mm 0.472 × 0.472 × t 0.039 in
20 % or less of operation distance (with standard sensing object)
Along sensing axis, perpendicular to sensing axis: 0.04 mm 0.0016 in or less
12
to
24
V
DC
+10
–15
% Ripple
P-P
10
%
or
less
15 mA or less
Output
NPN open-collector transistor
PNP open-collector transistor
• Maximum sink current: 100 mA
• Maximum source current: 100 mA
• Applied voltage: 30 V DC or less (between output and 0 V) • Applied voltage: 30 V DC or less (between output and +V)
• Residual voltage: 2 V or less (at 100 mA sink current)
• Residual voltage: 2 V or less (at 100 mA source current)
Utilization category
DC-12 or DC-13
Output operation
Normally closed
Normally closed
Normally closed
Normally closed
Max. response frequency
400 Hz
Operation indicator
Orange LED (lights up when the output is ON)
Pollution degree
3 (Industrial environment)
Protection
IP68 (IEC), IP68g (JEM) (Note 4, 5)
Ambient temperature
–25 to +70 °C –13 to +158 °F, Storage: – 40 to +85 °C – 40 to +185 °F
Ambient humidity
35 to 85 % RH, Storage: 35 to 95 % RH
EMC
EN 60947-5-2
Voltage withstandability
1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
50 MΩ, or more, with 500 V DC megger between all supply terminals connected together and enclosure
Vibration resistance
10 to 500 Hz frequency, 3 mm 0.118 in amplitude (Max. 20 G) in X, Y and Z directions for two hours each
Shock resistance
10,000 m/s2 acceleration (1,000 G approx.) in X, Y and Z directions for three times each
Sensing
range
variation
Material
Temperature characteristics
Voltage characteristics
Over ambient temperature range –25 to +70 °C –13 to +158 °F: Within ± 8 % of sensing range at +23 °C +73 °F
Within
±2
%
for
+10
–15
%
fluctuation
of
the
supply
voltage
Enclosure: PBT, Indicator part: Polyester
Cable
0.15 mm2 3-core oil, heat and cold resistant cabtyre cable, 1 m 3.281 ft long
Cable extension
Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight
15 g approx.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73 °F.
2) “ I ” in the model No. indicates a different frequency type.
3) The maximum operation distance stands for the maximum distance for which the sensor can detect the standard sensing object.
The stable sensing range stands for the sensing range for which the sensor can stably detect the standard sensing object even if there is an ambient
temperature drift and/or supply voltage fluctuation.
4) Panasonic Electric Works SUNX’s IP68 test method
1 Immerse at 0 m below 0 °C +32 °F water surface and leave for 30 min. Then, immerse at 0 m below +70 °C +158 °F water surface and leave for 30 min.
2 Regard the heat shock test in 1 as one cycle and perform 20 cycles.
3 Leave in water at a depth of 1 m 3.281 ft in water for 500 hours.
4 After tests 1 to 3 , insulation resistance, voltage withstandability, current consumption, and sensing range must meet the standard values.
5) If using the sensor in an environment where cutting oil droplets splatter, the sensor may be deteriorated due to added substances in the oil.
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
PLC /
TERMINALS
HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifier-
separated
GX-F/H
GXL
GL
GX-U/GX-FU/
GX-N
GX
6 Page 
GX-F/HRectangular-shaped Inductive Proximity Sensor
SERIES
772
SENSING CHARACTERISTICS (TYPICAL)
FIBER
SENSORS
GX-15 (Long sensing range) type
LASER
SENSORS
Sensing field
Standard sensing object Standard sensing object
Iron sheet 30 × 30 × t 1 mm Iron sheet 30 × 30 × t 1 mm
1.181 × 1.181 × t 0.039 in 1.181 × 1.181 × t 0.039 in
10 ℓ
0.394 L
ℓ
Top
sensing
Front
sensing
L
5
0.197
Correlation between sensing object size and sensing range
Sensing object Sensing object
a × a mm a × a in a × a mm a × a in
10
0.394
L
t 1mm L
t 0.039 in
Front sensing
t 1mm t 0.039 in
Top sensing Iron
Stainless steel
(SUS304)
5
0.197 Brass
Aluminum
As the sensing object size becomes smaller than
the standard size (iron sheet 30 × 30 × t 1 mm
1.181 × 1.181 × t 0.039 in), the sensing range
shortens as shown in the left figure.
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS
PRESSURE /
FLOW
SENSORS
0
10 5 0 5 10
0
10 20 30 40
0.394 0.197
0.197 0.394
0.394 0.787 1.181 1.575
Left Center Right
Sensing object side
Operating point ℓ (mm in)
length a (mm in)
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
PRECAUTIONS FOR PROPER USE
Refer to General precautions.
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
Mounting
GX-8 type
• Make sure to use a M3
(length: 12 mm 0.472 in or
more) truss head screw.
The tightening torque
should be 0.7 N·m or less.
Do not use a flat head
screw or a pan head
screw.
M3 (length 12 mm 0.472 in) truss head
screw (Accessory for MS-GXL8-4)
MS-GXL8-4 (Accessory)
M3 × 0.5 mm 0.020 in tapped hole
(Depth: 8 mm 0.315 in or more)
or ø3.4 mm ø0.134 in thru-hole
11.5 mm 0.453 in
If mounting using nut
and washers
(Accessories for MS-GXL8-4)
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
GX-6 type
• Use the optional sensor mounting bracket when
GX-12 type
installing.
• The tightening torque
should be 0.7 N·m or less.
<When using MS-GX6-1 (recommended)>
• To mount the sensor with
• To mount the sensor with
a nut, the mounting hole
diameter should be
ø3.4 mm ø0.134 in.
1 Insert the sensor into the
bracket as shown on the
right.
2 Push the sensor until the
Cable Hook
Groove
M3 pan head screw
(Purchase separately.)
MS-GX6-1
M3 x 0.5 mm 0.020 in
tapped hole or
ø3.4 mm ø0.134 in hole
a nut, the mounting hole
diameter should be ø3.4
mm ø0.134 in. Further, the
hole in which the boss is
inserted should be ø2.5
mm ø0.098 in and 3 mm
0.118 in, or more, deep.
bracket hook is lodged in
the groove on the upper
22 mm 0.866 in
GX-15 type
portion of the sensor.
3 Fix the bracket in place
with M3 pan head screw.
ø3.4 mm
ø0.134 in hole
If mounting using nut • The tightening torque
and washers
(Purchase separately.)
should be 1 N·m or less.
• To mount the sensor with
a nut, the mounting hole
<When using MS-GL6-1 / MS-GL6-2>
• To mount the sensor with a nut, the mounting hole
diameter should be ø3.4
mm ø0.134 in.
diameter should be ø3.4 mm ø0.134 in.
M3 pan head screws
(Purchase separately.)
M3 pan head screw
(Purchase separately.)
MS-GL6-1
MS-GL6-2
ø2.4 mm ø0.098 in hole
(Depth: 3 mm 0.315 in or more)
PLC /
TERMINALS
M3 (length 12 mm 0.472 in or more)
pan head screw
(Purchase separately.)
M3 × 0.5 mm 0.020 in tapped hole
(Depth: 10 mm 0.394 in or more)
or ø3.4 mm ø0.134 in thru-hole
HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS
FA
COMPONENTS
16 mm 0.630 in
If mounting using nut
and washers
(Purchase separately.)
ø2.5 mm ø0.098 in hole
(Depth: 3 mm 0.118 in or more)
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
9 mm
0.354 in
M3 pan head screws or
truss head screws
Do not use flat head
screws.
M3 x 0.5 mm 0.020 in
tapped holes or
ø3.4 mm ø0.134 in holes
If mounting using nuts
and washers
(Purchase separately.)
MS-GXL15
(Sensor mounting bracket)
Selection
Guide
Amplifier
Built-in
Amplifier-
separated
GX-F/H
GXL
GL
GX-U/GX-FU/
GX-N
GX
13.6 mm
0.535 in
M3 x 0.5 mm 0.020 in
tapped holes or
ø3.4 mm ø0.134 in holes
ø2.4 mm
0.098 in hole
10 mm
0.394 in
If mounting using nuts
and washers
(Purchase separately.)
M3 x 0.5 mm 0.020 in
tapped hole or
ø3.4 mm ø0.134 in hole
If mounting using nut
and washers
(Purchase separately.)
• When installing the long
sensing range type on iron
or stainless steel plate, put
the optional aluminum sheet
in between the sensor and
the plate.
Aluminum sheet (Optional)
• MS-A15F
• MS-A15H
12 Page | ||
| Seiten | Gesamt 16 Seiten | |
| PDF Download | [ GX-F8A-P Schematic.PDF ] | |
Link teilen
Besondere Datenblatt
| Teilenummer | Beschreibung | Hersteller |
| GX-F8A-P | Rectangular-shaped Inductive Proximity Sensor | Omron |
| Teilenummer | Beschreibung | Hersteller |
| CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
 Fairchild Semiconductor |
| KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
 KEC |
| www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |