|
|
PDF ECJCV50J106M Data sheet ( Hoja de datos )
| Número de pieza | ECJCV50J106M | |
| Descripción | Multilayer Ceramic Chip Capacitors | |
| Fabricantes | Matsushita Electronic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ECJCV50J106M (archivo pdf) en la parte inferior de esta página. Total 28 Páginas | ||
|
No Preview Available !
http://www.Datasheet4U.com
1 page  
CLASSIFICATION
SPECIFICATIONS
SUBJECT
Multilayer Ceramic Chip Capacitor
Common Specifications (Class2 Large Capacitance)
No. 151S-ECJ-KGD38E
PAGE 2 of 7
DATE 23th. Apr. 2003
４．Operating Temperature Range
Shown in Individual Specification.
５．Performance
The performance of the capacitor and its test condition shall be specified in Table 2.
5.1 Pretreatment
Before test and measurements, the following pretreatment shall be applied when necessary.
5.1.1 Heat Treatment
The capacitors shall be kept in a temperature of 150+0/-10℃ for 1 hour and then shall be stored in a
room temperature for 48±4 hours, before initial measurement.
5.1.2 Voltage Treatment
A D. C. voltage shall be applied for 1 hour in the specified test condition and then shall be stored in a
room temperature for 48±4 hours, before initial measurement.
６．Test
Unless otherwise specified, all test and measurements shall be made at a temperature of 15～35℃ and at a
relative humidity of 45～75%.
If results obtained are doubted a further test should be carried out at a temperature of 20±2℃ and a relative
humidity of 60～70%.
７．Structure
The structure shall be in a monolithic form as shown in Fig. 1.
Ｆｉｇ．１
Ｔａｂｌｅ １
No. Name
① Dielectric
② Inner electrode
③ Substrate electrode
④ Intermediate electrode
⑤ External electrode
８．Product Place
・Hokkaido Matsushita Electric Co., Ltd. / 1037-2, Kamiosatsu, Chitose-shi, Hokkaido, Japan
・Matsushita Electric Devices (M) Sdn. Bhd. / No.1 Jalan Pelga 16/13, 4000 Shah Alam, Selanger, MALAYSIA
・Tianjin Matsushita Electronic Component Co., Ltd. / S9 4TH Sub-street west Xiqing Economic Development
Z one Tianjin
９. Receipt and Effective term of Specifications
(1) Please send back one copy of this specification after you stamp your company stamp in this specification.
If you do not it back even if three months have passed after the issue date mentioned in the cover of this
specification, we assume that the specification would be received.
(2) When either your company or our company has no offer by document until three months before the
termination of the expiry date mentioned in the cover of this specification, the expiry date of this
specification shall be continuously extended one more year every year.
In addition to the above, if revision is performed during effective term and you have confirmed, old
specification shall be invalidity
Note ;
5 Page 
CLASSIFICATION
SPECIFICATIONS
No. 151S-ECJ-SS001E
SUBJECT
Multilayer Ceramic Chip Capacitor
Common Specifications (Precautions for Use)
PAGE 1 of 12
DATE 1st. Apr. 2002
１．Cautions on Operation
If a chip stacked ceramic capacitor ( hereafter referred to as capacitor ) is troubled by its peripheral conditions
Such as use environment, design requirements, and installation requirements, it will be short-circuited at worst.
If it is used in the shorted state, a large current will flow through it when a voltage is applied which will heat
the capacitor body, and possibly burn the circuit board out .
Design and assembly cautions are described below. Confirm them sufficiently before use.
１．１ Design Cautions
１．１．１ Design of Circuit
１．１．１．１ Working temperature
The working temperature must be within the range specified in the delivery specification.
The working temperatures must not exceed the maximum working temperature
１．１．１．２ Working voltage
The voltage across the terminals of the capacitor must be equal to or less than the rated voltage.
Do not use the capacitor in a circuit where an abnormal voltage exceeding the rated voltage
(surge voltage, pulse voltage, electrostatic voltage) may be applied to the capacitor. The capacitor
may be shorted. If a DC voltage is superimposed with an AC voltage, take care that the peak
voltage (Vp - p) is equal to or less than the rated voltage.
Even if the voltage is equal to or less than the rated voltage, when the capacitor is used in a circuit
where a high frequency voltage or a steep pulse voltage is applied continuously to it, closely examine
the reliability of the capacitor.
If such a voltage is applied continuously to the capacitor, the service life of it will be affected.
１．１．１．３ Working current
If the capacitor causes a short-circuit at the secondary side of the power supply circuit, a large
current will flow through it to heat the capacitor body, and the circuit board may be burnt out.
Sufficiently examine the safety of use, and install a protective circuit if required.
１．１．１．４ Self-heating
When self-heating is caused by an AC voltage or a pulse voltage circuit, if the ambient temperature
around the capacitor in use is room temperature (about 25℃), take care so that a temperature rise
(a difference between the surface temperature of the capacitor and the ambient temperature around
it) comes within 20℃ or below.
The surface temperature of the capacitor including an amount increased by the self-heating must be
equal to or less than the maximum working temperature specified in the delivery specification.
For the temperature rise of the capacitor according to the use circuit conditions, check the actual
operating conditions of the equipment in use.
１．１．１．５ Limitation of use places
Do not use the capacitor in the places indicated below. It may cause a short-circuit.
(1) Peripheral environmental (weatherproofness) conditions
(a) Places where water or salt water is applied directly
(b) Places where dewatering state occurs
(c) Places where corrosive gases (hydrogen sulfide, sulfurous acid, chlorine, and ammonia) are
f illed out
(2) Places for which the requirements of vibration or impact are so severe as to exceed the range
s pecified in the delivery specification.
Note ;
Ceramic Business Unit LCR Device Company
Matsushita Electronic Components Co.,Ltd.
Kad oma, Osaka, Japan
APPROVAL CHECK DESIGN
H.Itow
Y.Tsutsumi K.Ohishi
11 Page | ||
| Páginas | Total 28 Páginas | |
| PDF Descargar | [ Datasheet ECJCV50J106M.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ECJCV50J106M | Multilayer Ceramic Chip Capacitors | Matsushita Electronic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |