|
|
PDF E3T Data sheet ( Hoja de datos )
| Número de pieza | E3T | |
| Descripción | The Improved E3T Series | |
| Fabricantes | OMRO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de E3T (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
|
No Preview Available !
New Product News
Ultracompact, Ultrathin Photoelectric Sensor with Built-in Amplifier
E3T
The Improved E3T Series with Easier,
Smoother Mounting and Installation
• Newly added Through-beam, Long-distance (2 m) Sensors
(E3T-ST3@).
• Easy installation with M3-mounting Sensors
(E3T-ST@@M, E3T-FD@@M, and E3T-SL@@M).
• Small Cylindrical Sensors for one-point mounting also added to the Series.
(E3T-C@@@(S)).
Be sure to read Safety Precautions on page 13.
Lineup Overview
Appearance
Side-view
Sensing
method
Through-beam
Retro-
reflective
Diffuse-
reflective
Convergent-
reflective
BGS-
reflective
M2-mounting
●
●
---
●
---
M3-mounting
●
---
---
●
---
Rectangular
type
Flat
M2-mounting
●
---
●
---
●
M3-mounting
---
---
●
---
---
Top-view
--- ● --- ● --- ---
Cylindrical
type
Side-view
--- ● --- --- --- ---
http://www.Datasheet4U.com
1
1 page  
E3T
Accessories for M3-mounting Sensors These accessories are not included with the Sensor. Order them separately if required.
Name
Applicable
Sensor
Slits for Through-beam
Side-view Sensors
E3T-ST1@M
0.5
dia. E3T-ST2@M
E3T-ST1@M
1 dia.
E3T-ST2@M
Mounting Bracket for Side-view
Sensors *1
E3T-S@@@M
Model
E39-S76A
E39-S76B
E39-L166
Quantity
2
(One each for
Emitter and
Receiver)
Dimensions
page
19
Remarks
Sensing distance 100 mm,
Minimum detectable object (typical) 0.5-mm dia.
Sensing distance 30 mm,
Minimum detectable object (typical) 0.5-mm dia.
Sensing distance 300 mm,
Minimum detectable object (typical) 1-mm dia.
Sensing distance 100 mm,
Minimum detectable object (typical) 1-mm dia.
Nut plate provided
Mounting Bracket for Flat Sensors
E3T-FD@@M
Back-mounting Spacer for Flat Sen-
sors
E39-L167
E39-L168
12 2 ---
Use this Spacer when mounting a Flat Sensor
(E3T-FD@@M) from the back.
SUS Screw Set for Flat Sensors *2 E3T-FD@@M
SUS Screw Set for Side-view Sen-
sors *1*2
E3T-S@@@M
E39-L170
E39-L171
2
2 for each
Material: SUS304
Contents: Bolt with hexagonal hole (M3×6)
---
Material: SUS304
Contents: Bolt with hexagonal hole (M3×15), Hex-
agonal nuts, Spring washers, Flat washers
*1.When using Through-beam Sensors (E3T-ST@@M), order one bracket for the Emitter and one for the Receiver.
*2. This is the Screw Set for mounting the Sensor to the Mounting Bracket. Order this Set if you loose the screws. Do not use this Screw Set to mount the Mounting
Bracket to the equipment.
Accessories for Small Cylindrical Sensors
Name
Applicable
Sensor
Model
Quantity
Dimensions
Page
Remarks
SUS Nut Set for Through-beam
Sensors *1
E3T-CT@@
E3T-CT@@S
SUS Nut Set for Diffuse-reflective
Sensors
E3T-CD@@
E39-M5
E39-M6
4 (Hexagonal
nuts),
2 (Toothed
washers)
2 (Hexagonal
nuts),
1(Toothed
washers)
Material: SUS303
(Same type as provided with the Sensor.)
---
Adjustment Driver for Diffuse-reflec-
tive Sensors
E39-G17
1
This Driver is used to turn the sensitivity adjuster.
Provided with E3T-CD@@
*1.This Nut Set is for the Emitter/Receiver. This is the Nut Set for mounting the Sensor. Order this Set if you loose the screws.
Accessories for All Sensors
Name
Small Reflectors
(for Retro-reflective Sensors)
Tape Reflectors
(for Retro-reflective Sensors)
Applicable
Sensor
E3T-SR4@
Model
E39-R4
E3T-SR4@-S
E3T-SR4@-C
E39-R37-CA *2
E39-RS1-CA *2
E39-RS2-CA *2
E39-RS3-CA *2
Quantity
1
Dimensions
Page
18
19
Remarks
Sensing distance 200 mm [30 mm] *1
Minimum detectable object 2-mm dia.
Provided with the E3T-SR4@
Sensing distance 100 mm [10 mm] *1
Minimum detectable object 2-mm dia.
Provided with the E3T-SR4@-S
Sensing distance 100 mm [10 mm] *1
Minimum detectable object 2-mm dia.
Use Tape Reflectors in combination
with the E3T-SR4@-C, which
does not come with a Reflector.
*1.Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
*2. The E3T-SR4@ cannot be used with the E39-R37 or E39-RS1/2/3 (without CA) Tape Reflectors.
The E39-@-CA Reflector is for use only with the E3T-SR4@. It cannot be used with other Sensors.
Sensor I/O Connectors
(Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
Size
M12
(For -M1TJ models)
e-CON
Cable
Standard
cable
Straight
Appearance
Connector on one end
Connector on both ends
Cable type
2m
5m
2m
5 m 4-wire
0.5 to 1 m
Model
XS5F-D421-D80-A
XS5F-D421-G80-A
E39-ECON2M
E39-ECON5M
E39-ECONW@M
1.1 to 1.5 m
1.6 to 2 m
Replace @ with the cable length in
0.1-m increments.
Note: When using Through-beam Sensors, order one connector for the Emitter and one for the Receiver.
5
5 Page 
E3T
E3T-FL2@
40
30
20
Sensing Distance Characteristics of Sensitivity Adjustment Unit
(when Completing Optical Axis Adjustment)
E3T-ST1@ + E39-E10 Sensitivity Adjustment Unit
E3T-ST3@ + E39-E10 Sensitivity Adjustment Unit
3.5
3.0
2.5
E3T-ST3@
2.0
1.5
10
0
Material
Small Cylindrical Sensors
Parallel Operating Range
Through-beam
E3T-CT1@
80
60
40 X
Y
20
0
0.25
−20
0.5 0.75 1.0 1.25 1.5 1.75
Distance X (m)
−40
−60
−80
Operating Range
Diffuse-reflective
E3T-CD1@
20
Sensing object:
15 100 x 100 mm white paper
X
Y
10
5
0 10 20 30 40 50 60 70 80
Distance X (m)
−5
−10
−15
−20
1.0
E3T-ST1@
0.5
0
Min 1/3 1/2 2/3 Max
Adjustment dial angle
E3T-CT2@S (Top to Bottom)
200
X
150 Y
100
50
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Distance X (m)
−50
−100
−150
−200
Sensing Distance vs. Material
Diffuse-reflective
E3T-CD1@
120
110
100
90
80
70
60
50
40
30
20
10
0
E3T-CT2@S (Right to Left)
200
X
150 Y
100
50
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
−50 Distance X (m)
−100
−150
−200
Material
11
11 Page | ||
| Páginas | Total 24 Páginas | |
| PDF Descargar | [ Datasheet E3T.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| E30 | Miniature LEDs |  Gilway Technical Lamp |
| E301 | Diode ( Rectifier ) |  American Microsemiconductor |
| E304-12V | T-1 and T-1 3/4/ Infrared LEDs | Gilway Technical Lamp |
| E304-5V | T-1 and T-1 3/4/ Infrared LEDs | Gilway Technical Lamp |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |