|
|
PDF ADUM6010 Data sheet ( Hoja de datos )
| Número de pieza | ADUM6010 | |
| Descripción | Integrated DC-to-DC Converter | |
| Fabricantes | Analog Devices | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ADUM6010 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
Data Sheet
FEATURES
isoPower integrated, isolated dc-to-dc converter
Regulated 3.15 V to 5.25 V output
Up to 150 mW output power
20-lead SSOP package with 5.3 mm creepage
High temperature operation: 105°C
High common-mode transient immunity: >25 kV/µs
Safety and regulatory approvals
UL recognition (pending)
3750 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice #5A (pending)
VDE certificate of conformity (pending)
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIORM = 849 V peak
APPLICATIONS
Power supply start-up bias and gate drives
Isolated sensor interfaces
Industrial PLCs
GENERAL DESCRIPTION
The ADuM60101 is an integrated, isolated dc-to-dc converter.
Based on the Analog Devices, Inc., iCoupler® technology, the
dc-to-dc converter provides regulated, isolated power, adjustable
between 3.15 V and 5.25 V. Input supply voltages can range
from slightly below the required output to significantly higher.
Popular combination and their associated power levels are shown
in Table 1.
The iCoupler chip-scale transformer technology is used for isolated
logic signals and for the magnetic components of the dc-to-dc
converter. The result is a small form factor, total isolation
solution.
isoPower uses high frequency switching elements to transfer
power through its transformer. Special care must be taken
during printed circuit board (PCB) layout to meet emissions
standards. See the AN-0971 Application Note for board layout
recommendations.
Integrated DC-to-DC Converter
ADuM6010
FUNCTIONAL BLOCK DIAGRAM
NC 1
GNDP 2
NC 3
NC 4
GNDP 5
GNDP 6
NC 7
PDIS 8
VDDP 9
GNDP 10
PCS
OSC
ADuM6010 20 NC
19 GNDISO
18 NC
17 NC
16 GNDISO
15 GNDISO
14 NC
13 VSEL
1.25V 12 VISO
RECT REG
11 GNDISO
Figure 1.
Table 1. Power Levels
Input Voltage (V) Output Voltage (V)
55
5 3.3
3.3 3.3
Output Power (mW)
150
100
100
1 Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329. Other patents are pending.
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibilityisassumedbyAnalogDevices for itsuse,nor foranyinfringementsofpatentsor other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2012–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
Free Datasheet http://www.datasheet4u.com/
1 page  
Data Sheet
ADuM6010
ELECTRICAL CHARACTERISTICS—5 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY
All typical specifications are at TA = 25°C, VDDP = 5.0 V, VISO = 3.3 V, VSEL resistor network: R1 = 10 kΩ, R2 = 16.2 kΩ. Minimum/maximum
specifications apply over the entire recommended operation range which is 4.5 V ≤ VDDP ≤ 5.5 V, 3.0 V ≤ VISO ≤ 3.6 V, and −40°C ≤ TA ≤
+105°C, unless otherwise noted. Switching specifications are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted.
Table 6. DC-to-DC Converter Static Specifications
Parameter
Symbol Min Typ Max Unit
Test Conditions/Comments
DC-TO-DC CONVERTER SUPPLY
Setpoint
VISO 3.3 V IISO = 15 mA, R1 = 10 kΩ, R2 = 16.9 kΩ
Thermal Coefficient
VISO (TC)
−26 μV/°C
Line Regulation
VISO (LINE)
20
mV/V
IISO = 15 mA, VDD1 = 4.5 V to 5.5 V
Load Regulation
VISO (LOAD)
1.3 3
%
IISO = 3 mA to 27 mA
Output Ripple
VISO (RIP) 50 mV p-p 20 MHz bandwidth, CBO = 0.1 µF||10 µF, IISO = 27 mA
Output Noise
VISO (NOISE) 130 mV p-p CBO = 0.1 µF||10 µF, IISO = 27 mA
Switching Frequency
fOSC
125 MHz
Pulse Width Modulation Frequency fPWM
600 kHz
Output Supply
IISO (MAX)
30
mA 3.6 V > VISO > 3 V
Efficiency at IISO (MAX)
24 % IISO = 27 mA
IDD1, No VISO Load
IDD1 (Q)
3.2 8
mA
IDD1, Full VISO Load
IDD1 (MAX)
85
mA
Thermal Shutdown
Shutdown Temperature
154 °C
Thermal Hysteresis
10 °C
Table 7. Input and Output Characteristics
Parameter
Symbol Min
DC SPECIFICATIONS
Logic High Input Threshold VIH
0.7 VDDP
Logic Low Input Threshold VIL
Undervoltage Lockout
Positive Going Threshold VUV+
Negative Going Threshold VUV−
Input Currents per Channel IPDIS
−10
Typ
2.7
2.4
+0.01
Max
0.3 VDDP
+10
Unit Test Conditions/Comments
V
V
VISO, VDDP supply
V
V
µA 0 V ≤ VPDIS ≤ VDDP
Rev. A | Page 5 of 16
Free Datasheet http://www.datasheet4u.com/
5 Page 
Data Sheet
90% LOAD
10% LOAD
(1ms/DIV)
Figure 10. Typical Transient Load Response, 5 V Input, 3.3 V Output,
10% to 90% Load Step
4.970
4.965
4.960
4.955
4.950
4.945
4.940
01234
TIME (µs)
Figure 11. Typical VISO = 5 V Output Voltage Ripple at 90% Load
3.280
3.278
3.276
3.274
3.272
3.270
01234
TIME (µs)
Figure 12. Typical VISO = 3.3 V Output Voltage Ripple at 90% Load
ADuM6010
5.0
4.5
4.0
3.5
3.0
30mA LOAD
2.5 20mA LOAD
10mA LOAD
2.0
3.0 3.5 4.0 4.5 5.0 5.5 6.0
OUTPUT VOLTAGE (V)
Figure 13. Relationship Between Output Voltage and Required Input Voltage,
Under Load, to Maintain >80% Duty Factor in the PWM
500
450
400
350
300
250
VDDP = 5V/VISO = 5V
200
VDDP = 5V/VISO = 3.3V
150
100
–40
–20
0 20 40 60 80
AMBIENT TEMPERATURE (°C)
100 120
Figure 14. Power Dissipation with a 30 mA Load vs. Temperature
500
450
VDDP = 5V/VISO = 5V
400 VDDP = 3.3V/VISO = 3.3V
VDDP = 5V/VISO = 3.3V
350
300
250
200
150
100
–40
–20
0 20 40 60 80
AMBIENT TEMPERATURE (°C)
100 120
Figure 15. Power Dissipation with a 20 mA Load vs. Temperature
Rev. A | Page 11 of 16
Free Datasheet http://www.datasheet4u.com/
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet ADUM6010.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ADUM6010 | Integrated DC-to-DC Converter | Analog Devices |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |