|
|
PDF GS2974A Data sheet ( Hoja de datos )
| Número de pieza | GS2974A | |
| Descripción | HD-LINX III Adaptive Cable Equalizer | |
| Fabricantes | Gennum | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GS2974A (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
GS2974A HD-LINX™ III Adaptive Cable Equalizer
Features
• SMPTE 424M, SMPTE 292M and SMPTE 259M
compliant
• Automatic cable equalization
• 0.3UI Maximum Output Jitter at 2.97Gb/s
• Multi-standard operation from 143Mb/s to 2.97Gb/s
• Supports DVB-ASI at 270Mb/s
• Small footprint (4mm x 4mm)
• Pb-free and RoHS compliant
• Manual bypass (useful for low data rates with slow
rise/fall times)
• Performance optimized for 1.485Gb/s and 2.97Gb/s
• Typical equalized length of Belden 1694A cable: 120m
at 2.97Gb/s, 200m at 1.485Gb/s, and 350m at 270Mb/s
• 50Ω differential output (internal 50Ω pull-ups)
• Programmable mute based on max cable length adjust
• Single 3.3V power supply operation
• Operating temperature range: 0°C to +70°C
Applications
• SMPTE 424M, SMPTE 292M and SMPTE 259M Coaxial
Cable Serial Digital Interfaces.
Description
The GS2974A is a high-speed BiCMOS integrated circuit
designed to equalize and restore signals received over 75Ω
co-axial cable.
The GS2974A is designed to support SMPTE 424M, SMPTE
292M and SMPTE 259M, and is optimized for performance
at 1.485Gb/s and 2.97Gb/s.
The GS2974A features DC restoration to compensate for
the DC content of SMPTE pathological test patterns.
A voltage programmable mute threshold (MCLADJ),
applicable for SD mode (refer to Section 4.3), is included to
allow muting of the GS2974A output when an approximate
selected cable length is reached for SMPTE 259M signals.
This feature allows the GS2974A to distinguish between
low amplitude SD-SDI signals and noise at the input of the
device. The serial digital outputs of the GS2974A may be
forced to a mute state by applying a voltage to the MUTE
pin.
Power consumption is typically 215mW using a 3.3V
power supply. The GS2974A is lead-free, and the
encapsulation compound does not contain halogenated
flame retardant.
This component and all homogeneous subcomponents are
RoHS compliant.
MCLADJ
SDI
SDI
CABLE LENGTH ADJUSTOR
CARRIER
DETECT MUTE
EQUALIZER
DC RESTORE
OUTPUT
AGC
GS2974A Functional Block Diagram
GS2974A HD-LINX™ III Adaptive Cable Equalizer
Data Sheet
42216 - 3
January 2009
www.gennum.com
CD
MUTE
BYPASS
SDO
SDO
1 of 16
Free Datasheet http://www.datasheet4u.com/
1 page  
Table 1-1: GS2974A Pin Descriptions (Continued)
Pin Number
10, 11
12
Name
SDO, SDO
VEE_D
Timing
Analog
Analog
Type
Output
Power
13
VCC_D
Analog
Power
14
MUTE
Not
Input
Synchronous
15 CD Not Output
Synchronous
16
VCC_A
Analog
Power
–
Center Pad
–
Power
Description
Equalized serial digital differential output.
Most negative power supply for the digital circuitry and output
buffer.
Connect to GND.
Most positive power supply for the digital I/O pins of the device.
Connect to +3.3V DC.
CONTROL SIGNAL INPUT
levels are LVCMOS/LVTTL compatible. (3.3V Tolerant)
Controls output behaviour on SDO and SDO
See Section 4.4.
STATUS SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Indicates the presence of a good input signal.
See Section 4.4.
Most positive power supply for the analog circuitry of the device.
Connect to +3.3V DC.
Internally bonded to VEE_A.
GS2974A HD-LINX™ III Adaptive Cable Equalizer
Data Sheet
42216 - 3
January 2009
5 of 16
Free Datasheet http://www.datasheet4u.com/
5 Page 
does not solve this problem, since the signal to noise ratio on the circuit board could be
significantly less than the default signal detection level set by the on chip reference.
NOTE: MCLADJ is only recommended for data rates up to 360Mb/s. For data rates above
this, MCLADJ should be left floating.
4.4 Mute and Carrier Detect
The GS2974A includes a MUTE input pin that allows the application interface to mute the
serial digital output at any time. Set the MUTE pin HIGH to mute SDO and SDO. In this
case, the outputs will mute regardless of the setting of the BYPASS pin.
A Carrier Detect output pin (CD) indicates the presence of a valid signal at the input of
the GS2974A. When CD is LOW, the device has detected a valid input on SDI and SDI.
When CD is HIGH, the device has not detected a valid input.
NOTE: This pin may be connected directly to the CD pin to allow mute on loss of carrier.
NOTE: CD will only detect loss of carrier for data rates greater than 19Mb/s. The CD
output pin may be connected directly to the MUTE input pin to enable automatic muting
of the GS2974A when no valid input signal has been detected.
NOTE: If the maximum cable length is exceeded and the device is not in bypass mode
the GS2974A will not assert the CD pin even if a carrier is present.
Table 4-1: Mute Input Table
Mute
0
1
Function
SDO and SDO operate normally
SDO and SDO are forced to a steady
state
Table 4-2: CD Output Table
CD
0
1
Input Status
Valid Input on SDI, SDI pins
Input is not valid
GS2974A HD-LINX™ III Adaptive Cable Equalizer
Data Sheet
42216 - 3
January 2009
11 of 16
Free Datasheet http://www.datasheet4u.com/
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet GS2974A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GS2974A | HD-LINX III Adaptive Cable Equalizer | Gennum |
| GS2974B | HD-LINX III Adaptive Cable Equalizer | Gennum |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |