|
|
PDF PT4115 Data sheet ( Hoja de datos )
| Número de pieza | PT4115 | |
| Descripción | 1.2A Step-down High Brightness LED Driver | |
| Fabricantes | PowTech | |
| Logotipo |  |
|
 1. - 1.2A Step-down LED Driver  Hay una vista previa y un enlace de descarga de PT4115 (archivo pdf) en la parte inferior de esta página. Total 18 Páginas | ||
|
No Preview Available !
PT4115
30V, 1.2A Step-down High Brightness
LED Driver with 5000:1 Dimming
GENERAL DESCRIPTION
The PT4115 is a continuous conduction mode inductive
step-down converter, designed for driving single or
multiple series connected LED efficiently from a
voltage source higher than the total LED chain voltage.
The device operates from an input supply between 6V
and 30V and provides an externally adjustable output
current of up to 1.2A. Depending upon the supply
voltage and external components, the PT4115can
provide more than 30 watts of output power.
The PT4115 includes the power switch and a high-side
output current sensing circuit, which uses an external
resistor to set the nominal average output current, and a
dedicated DIM input accepts either a DC voltage or a
wide range of pulsed dimming. Applying a voltage of
0.3V or lower to the DIM pin turns the output off and
switches the device into a low current standby state.
The PT4115 is available in SOT89-5 and ESOP8
packages.
FEATURES
Simple low parts count
Wide input voltage range: 6V to 30V
Up to 1.2A output current
Single pin on/off and brightness control using DC
voltage or PWM
Up to 1MHz switching frequency
Typical 5% output current accuracy
Inherent open-circuit LED protection
High efficiency (up to 97%)
High-Side Current Sense
Hysteretic Control: No Compensation
Adjustable Constant LED Current
ESOP8 package for large output power application
RoHS compliant
APPLICATIONS
Low voltage halogen replacement LEDs
Automotive lighting
Low voltage industrial lighting
LED back-up lighting
Illuminated signs
SELV lighting
LCD TV backlighting
ORDERING INFORMATION
PACKAGE
SOT89-5
TEMPERATURE
RANGE
-40 oC to 85 oC
ORDERING PART
NUMBER
PT4115B89E:A type
PT4115B89E-B:B type
ESOP8
-40 oC to 85 oC
PT4115BSOH:A type
PT4115BSOH-B:B type
Note:
xxxxxX
Assembly Factory Code
Lot Number
TRANSPORT
MEDIA
Tape and Reel
1000 units
Tape and Reel
2500 units
MARKING
PT4115
xxxxxX
PT4115
xxxxxX
TYPICAL APPLICATION CIRCUIT
DC6-30V
VIN
AC12-18V
CIN 100uF
RS
0.13Ω
D
LED
3W
L
68uH
VIN CSN SW
DIM PT4115
GND
China Resources Powtech (Shanghai) Limited
PT4115_DS Rev EN_2.9
WWW.CRPOWTECH.COM
Page 1
Free Datasheet http://www.datasheet4u.com/
1 page  
PT4115
30V, 1.2A Step-down High Brightness
LED Driver with 5000:1 Dimming
OPERATION DESCRIPTION
The device, in conjunction with the coil (L1) and
current sense resistor (RS), forms a self oscillating
continuous-mode buck converter.
When input voltage VIN is first applied, the initial
current in L1 and RS is zero and there is no output from
the current sense circuit. Under this condition, the
output of CS comparator is high. This turns on an
internal switch and switches the SW pin low, causing
current to flow from VIN to ground, via RS, L1 and the
LED(s). The current rises at a rate determined by VIN
and L1 to produce a voltage ramp (VCSN) across RS.
When (VIN-VCSN) > 115mV, the output of CS
comparator switches low and the switch turns off. The
current flowing on the RS decreases at another rate.
When (VIN-VCSN) < 85mV, the switch turns on again
and the mean current on the LED is determined by
(
85+ 115
2
mV
)
/
RS
=
100mV
/ RS
.
The high-side current-sensing scheme and on-board
current-setting circuitry minimize the number of
external components while delivering LED current with
±5% accuracy, using a 1% sense resistor.
The PT4115 allow dimming with a PWM signal at the
DIM input. A logic level below 0.3V at DIM forces
PT4115 to turn off the LED and the logic level at DIM
must be at least 2.5V to turn on the full LED current.
The frequency of PWM dimming ranges from 100Hz to
more than 20 kHz.
The DIM pin can be driven by an external DC voltage
(VDIM) to adjust the output current to a value below the
nominal average value defined by RS. The DC voltage
is valid from 0.5V to 2.5V. When the dc voltage is
higher than 2.5V, the output current keeps constant.
The LED current also can be adjusted by a resistor
connected to the DIM pin. An internal pull-up resistor
(typical 200KΩ) is connected to a 5V internal regulator.
The voltage of DIM pin is divided by the internal and
external resistor.
The DIM pin is pulled up to the internal regulator (5V)
by a 200KΩ resistor. It can be floated at normal
working. When a voltage applied to DIM falls below
the threshold (0.3V nom.), the output switch is turned
off. The internal regulator and voltage reference remain
powered during shutdown to provide the reference for
the shutdown circuit. Quiescent supply current during
shutdown is nominally 95uA and switch leakage is
below 5uA.
Additionally, to ensure the reliability, the PT4115 is
built with a thermal shutdown (TSD) protection and a
thermal pad. The TSD protests the IC from over
temperature (160℃). Also the thermal pad enhances
power dissipation. As a result, the PT4115 can handle a
large amount of current safely.
China Resources Powtech (Shanghai) Limited
PT4115_DS Rev EN_2.9
WWW.CRPOWTECH.COM
Page 5
5 Page 
PT4115
30V, 1.2A Step-down High Brightness
LED Driver with 5000:1 Dimming
APPLICATION NOTES
Setting nominal average output current with
external resistor RS
The nominal average output current in the LED(s) is
determined by the value of the external current sense
resistor (RS) connected between VIN and CSN and is
given by:
IOUT 0.1/ Rs (Rs 0.082)
This equation is valid when DIM pin is float or applied
with a voltage higher than 2.5V (must be less than 5V).
Actually, RS sets the maximum average current which
can be adjusted to a less one by dimming.
Output current adjustment by external DC control
voltage
The DIM pin can be driven by an external dc voltage
(VDIM), as shown, to adjust the output current to a
value below the nominal average value defined by RS.
VIN
RS
0.13Ω
LED
3W
D
L
68uH
cycle PWM can be applied to the DIM pin, as shown
below, to adjust the output current to a value below the
nominal average value set by resistor RS:
I
OUT
0.1
Rs
D
(0 D 100%,2.5V Vpulse 5V )
I OUT
Vpulse 0.1 D
2.5 Rs
(0 D 100%,0.5V Vpulse 2.5V )
RS
VIN
0.13Ω
LED
3W
L
68uH
D
VIN
CSN
SW
DIM PT4115
VIN
CSN
SW
GND
DIM PT4115
GND
The average output current is given by:
I OUT
0.1VDIM
2.5 Rs
(0.5V VDIM
2.5V )
Note that 100% brightness setting corresponds to:
(2.5V VDIM 5V )
Output current adjustment by PWM control
A Pulse Width Modulated (PWM) signal with duty
PWM dimming provides reduced brightness by
modulating the LED’s forward current between 0% and
100%. The LED brightness is controlled by adjusting
the relative ratios of the on time to the off time. A 25%
brightness level is achieved by turning the LED on at
full current for 25% of one cycle. To ensure this
switching process between on and off state is invisible
by human eyes, the switching frequency must be
greater than 100 Hz. Above 100 Hz, the human eyes
average the on and off times, seeing only an effective
brightness that is proportional to the LED’s on-time
duty cycle. The advantage of PWM dimming is that the
forward current is always constant, therefore the LED
color does not vary with brightness as it does with
analog dimming. Pulsing the current provides precise
brightness control while preserving the color purity.
The dimming frequency of PT4115 can be as high as 20
kHz.
China Resources Powtech (Shanghai) Limited
PT4115_DS Rev EN_2.9
WWW.CRPOWTECH.COM
Page 11
11 Page | ||
| Páginas | Total 18 Páginas | |
| PDF Descargar | [ Datasheet PT4115.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PT4110 | 15 Watt 48V Isolated DC-DC Converter (Rev. A) |  Texas Instruments |
| PT4110 | Side View and Thin Flat Type Phototransistors |  Sharp Electrionic Components |
| PT4110 | High Efficiency White LED Driver |  Powtech |
| PT4110E89E | High Efficiency White LED Driver | Powtech |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |