Datenblatt-pdf.com


DS3HHG-01 Schematic ( PDF Datasheet ) - Pentair

Teilenummer DS3HHG-01
Beschreibung Self-Priming Centrifugal Pump
Hersteller Pentair
Logo Pentair Logo 




Gesamt 12 Seiten
DS3HHG-01 Datasheet, Funktion
OWNER’S MANUAL
Self-Priming Centrifugal Pump
“DS3” Series
3621 1199 ASB
Installation/Operation/Parts
For further operating, installation,
or maintenance assistance:
Call 888-782-7483
293 WRIGHT STREET, DELAVAN, WI 53115 WWW.sta-rite.COM
PH: 888-782-7483
© 2012 Pentair, Inc. All Rights Reserved.
S536 (11/08/12)
Free Datasheet http://www.datasheet4u.com/






DS3HHG-01 Datasheet, Funktion
Electrical
6
Connection diagram for dual voltage, single-phase
motors. Your dual-voltage motor’s terminal board (under
the motor end cover) will match one of the diagrams
below. Follow that diagram if necesary to convert motor
to 115 Volt power.
Connect power supply wires to L1 and L2. For 3-phase
motors, or if motor does not match these pictures, follow
the connection diagram on the motor nameplate.
Motor Switch Settings
Dual-voltage motors (motors that can operate at either
115 or 230 volts), are set at the factory to 230 volts. Do
not change motor voltage setting if line voltage is 230
volts, or if you have a single voltage motor.
NOTICE: Never wire a 115 volt motor to a 230 volt line.
Remove Motor End Cover
If you have a dual-voltage motor, and will connect it to
115 volts, follow the procedure below.
End Cover Screws
Motor
End Cover
Figure 6: Removing Motor End Cover
4693
You will need to remove the motor end cover to change
the voltage setting.
Your motor terminal board (located under the motor end
cover) should look like one of those below.
Plug Type Voltage Selector
To change to 115 volts:
1. Make sure power is off.
2. Pull the plug straight up.
3. Move and attach the plug at the 115 volt position.
The plug will now cover 2 metal tabs. The arrow on
the plug will point to 115V.
4. Attach the power lead wires to the power lead
terminals. Make sure the wires are secure.
Ground
Screw
Voltage Change
Plug
Power Lead
Terminals
Figure 7: Voltage set to 230 volts, Plug46T94ype
5. Attach the ground wire to the green ground screw
6. Reinstall the Motor end cover
Go to Wiring Connections below.
Dial Type Voltage Selector
Ground
Screw
Voltage
Change Dial
Power Lead
Terminals
Figure 8: Voltage set to 230 volts, Dial Type
4695
To change to 115 volts:
1. Make sure power is off.
2. Turn the dial counter-clockwise until 115 shows in
the dial window.
3. Attach the power lead wires to the power lead
terminals. Make sure the wires are secure.
4. Attach the ground wire to the green ground screw
5. Reinstall the Motor end cover
Go to Wiring Connections below.
Hazardous voltage. Can shock, burn, or
cause death. Disconnect power to motor before
working on pump or motor. Ground motor before
connecting to power supply.
WIRING CONNECTIONS
Ground motor before connecting to electrical
power supply. Failure to ground motor can cause
severe or fatal electrical shock hazard.
Do not ground to a gas supply line.
To avoid dangerous or fatal electrical shock, turn
OFF power to motor before working on electrical
connections.
Supply voltage must be within ±10% of nameplate
voltage. Incorrect voltage can cause fire or damage
motor and voids warranty. If in doubt consult a licensed
electrician.
Use wire size specified in Wiring Chart, Page 7. If
possible, connect pump to a separate branch circuit
with no other appliances on it.
Wire motor according to diagram on motor
nameplate. If nameplate diagram differs from
diagrams above, follow nameplate diagram.
1. Install, ground, wire and maintain this pump in
accordance with electrical code requirements.
Consult your local building inspector for information
about codes.

6 Page









DS3HHG-01 pdf, datenblatt
Repair Parts
1
3621 1199SPC
13
14
12
15
2
34
5
6A
11
6
7
8
7A
12
9
Key
Part
No.
Description
Qty.
1 Motor, 115/230V, 1 Phase
1 Motor, 230/460V, 3 Phase
2 Water Slinger
3 Seal Plate
4 Gasket - Seal Plate
5 Shaft Seal
6 Impeller (1 Phase)
6 Impeller (3 Phase)
6A Impeller Screw (1 Phase)
6A Impeller Screw (3 Phase)
7 Diffuser
7A Screw 10-24 x1” Lg Hex Head
7A Machine screw 8-32x7/8” Lg.
8 Diffuser Ring
9 Pump Body Assembly
10 Plug 1/4” NPT Hex Head
11 Base
12 3/8-16x1-1/4” Lower Capscrew
13 3/8-16x1” Upper Capscrew
14 Motor Pad
15 Capscrew 3/8-16x3/4” Lg
15 Capscrew 5/16-18x3/4” Lg.
• Lockwasher 3/8”
• Nut, 3/16”-18 Hex Head
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
2
2
1
6
8
2
2
DS3HE-01
DS3HE3-01
1 HP
J218-596PKG
AP100EL
17351-0009
C3-155
C20-86
U109-6A
C105-92PKB
C105-92PKBA
C30-14SS
C101-276P
U30-696SS
C21-10
C76-67
U78-941ZPV
C4-82
U30-75ZP
U30-74ZP
C35-5
U30-72ZP
U43-12ZP
U36-37ZP
• Not illustrated.
* Model DS3HHG3-01 uses Base C4-82.
10
MODEL NUMBER
DS3HF-01
DS3HF3-01
1-1/2 HP
DS3HG-01
DS3HG3-01
2 HP
J218-601PKG
AP100FL
17351-0009
C3-155
C20-86
U109-6A
C105-92PC
C105-92PCA
C30-14SS
C101-276P
U30-696SS
C21-10
C76-67
U78-941ZPV
C4-82
U30-75ZP
U30-74ZP
C35-5
U30-72ZP
U43-12ZP
U36-37ZP
J218-883APKG
AP100GL
17351-0009
C3-117
C20-87
U109-6A
C105-214PDA
C105-214PDA
C30-14SS
C30-14SS
C101-182
U30-53SS
C21-2
C76-68
U78-941ZPV
C4-82
U30-75ZP
U30-74ZP
C35-5
U30-60ZP
U43-12ZP
U36-37ZP
DS3HHG-01
DS3HHG3-01
2-1/2 HP
J218-628A
AP100G5L
17351-0009
C3-117
C20-87
U109-6A
C105-214PA
C105-214PA
C30-14SS
C30-14SS
C101-182
U30-53SS
C21-2
C76-68
U78-941ZPV
C4-82A*
U30-75ZP
U30-99SS
C35-5
U30-60ZP
U43-12ZP
U36-37ZP

12 Page





SeitenGesamt 12 Seiten
PDF Download[ DS3HHG-01 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
DS3HHG-01Self-Priming Centrifugal PumpPentair
Pentair

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche