Datenblatt-pdf.com


W25X16BV Schematic ( PDF Datasheet ) - Winbond

Teilenummer W25X16BV
Beschreibung 16M-BIT SERIAL FLASH MEMORY
Hersteller Winbond
Logo Winbond Logo 




Gesamt 30 Seiten
W25X16BV Datasheet, Funktion
www.DataSheet.co.kr
W25X16BV
16M-BIT
SERIAL FLASH MEMORY WITH
4KB SECTORS AND DUAL OUTPUT SPI
The W25Q16BV is recommended for all new 16Mb designs. The W25X16BV is
available for existing designs that require "25X" device ID for firmware
compatibility.
Publication Release Date: October 7, 2009
- 1- Preliminary -- Revision C
Datasheet pdf - http://www.DataSheet4U.net/






W25X16BV Datasheet, Funktion
www.DataSheet.co.kr
5. PAD CONFIGURATION PDIP 300-MIL
W25X16BV
Figure 1c. W25X16BV Pin Assignments, 8-pin PDIP (Package Code DA)
6. PIN DESCRIPTION SOIC 150 / 208-MIL, PDIP 300-MIL, WSON 6X5-MM
PIN NO.
1
2
3
4
5
6
7
8
PIN NAME
/CS
DO
/WP
GND
DIO
CLK
/HOLD
VCC
I/O FUNCTION
I Chip Select Input
O Data Output
I Write Protect Input
Ground
I/O Data Input / Output
I Serial Clock Input
I Hold Input
Power Supply
-6-
Datasheet pdf - http://www.DataSheet4U.net/

6 Page









W25X16BV pdf, datenblatt
www.DataSheet.co.kr
W25X16BV
11. CONTROL AND STATUS REGISTERS
The Read Status Register instruction can be used to provide status on the availability of the Flash
memory array, if the device is write enabled or disabled, and the state of write protection. The Write
Status Register instruction can be used to configure the device write protection features. See Figure 3.
11.1 STATUS REGISTER
11.1.1 BUSY
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing
a Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction. During
this time the device will ignore further instructions except for the Read Status Register instruction (see
tW, tPP, tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status register
instruction has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for
further instructions.
11.1.2 Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to a 1 after executing
a Write Enable Instruction. The WEL status bit is cleared to a 0 when the device is write disabled. A
write disable state occurs upon power-up or after any of the following instructions: Write Disable, Page
Program, Sector Erase, Block Erase, Chip Erase and Write Status Register.
11.1.3 Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, and BP0) are non-volatile read/write bits in the status register (S4,
S3, and S2) that provide Write Protection control and status. Block Protect bits can be set using the
Write Status Register Instruction (see tW in AC characteristics). All, none or a portion of the memory
array can be protected from Program and Erase instructions (see Status Register Memory Protection
table). The factory default setting for the Block Protection Bits is 0, none of the array protected. The
Block Protect bits can not be written to if the Status Register Protect (SRP) bit is set to 1 and the Write
Protect (/WP) pin is low.
11.1.4 Top/Bottom Block Protect (TB)
The Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the Top
(TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table.
The TB bit is non-volatile and the factory default setting is TB=0. The TB bit can be set with the Write
Status Register Instruction provided that the Write Enable instruction has been issued. The TB bit can
not be written to if the Status Register Protect (SRP) bit is set to 1 and the Write Protect (/WP) pin is
low.
11.1.5 Reserved Bits
Status register bit location S6 is reserved for future use. Current devices will read 0 for this bit
location. It is recommended to mask out the reserved bit when testing the Status Register. Doing this
will ensure compatibility with future devices.
- 12 -
Datasheet pdf - http://www.DataSheet4U.net/

12 Page





SeitenGesamt 30 Seiten
PDF Download[ W25X16BV Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
W25X16BV16M-BIT SERIAL FLASH MEMORYWinbond
Winbond

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche