Datenblatt-pdf.com


GP1FAV31TK0F Schematic ( PDF Datasheet ) - Sharp Electrionic Components

Teilenummer GP1FAV31TK0F
Beschreibung Fiber Optic Transmitter Square connector
Hersteller Sharp Electrionic Components
Logo Sharp Electrionic Components Logo 




Gesamt 8 Seiten
GP1FAV31TK0F Datasheet, Funktion
GP1FAV31TK0F
GP1FAV31TK0F
Fiber Optic Transmitter
Square connector
With mounting hole
With shutter
Description
GP1FAV31TK0F has a built-in LED with a
peak light emission wavelength of 660 nm and
the associated drive IC, and the input is TTL
level compatible.
Features
1. Fiber optic transmitter
(Receiver : GP1FAV31RK0F)
2. Square connector (JEITA RC-5720B)
3. With mounting hole
4. With shutter function
5. Supply voltage : 3 V
6. Transfer rate : 15.5 Mb/s
Agency approvals/Compliance
1. Compliant with JEITA RC-5720B and CP1201
2. Compliant with RoHS directive (2002/95/EC)
Applications
AV equipment
(DVD, CD, MD players etc.)
www.DataSheet4U.com
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: E2-A00601EN
Date Dec.01.2006
1 ©SHARP Corporation






GP1FAV31TK0F Datasheet, Funktion
GP1FAV31TK0F
Design and Production Notes
(1) Stabilization of power supply line
Please put a by-pass capacitor (0.1 μF) close to the device at least within 7 mm of the terminal.
Please also put a 4.7 μF capacitor across the power supply line nearby.
(2) Soldering condition
Solder at the condition within the absolute maximum ratings in this sheet. In case of using flow soldering, please make
sure of the conditions of process at the flow equipment. Also, do not use reflow soldering. In case of soldering by hand,
do not contact top of soldering iron to lead terminal directly. (Solder at a position more than 1.6 mm away from the base
of the lead terminal.)
(3) About getting dirt and dust in the connector coupling portion
In case dirt or dust comes into the connector coupling portion, please use a blower to take it off.
Any rigid rod-like object must not be inserted since into the coupling portion.
The internal device might be damaged, resulting deteriorated characteristics.
(4) Cleaning
Do not immerse for cleaning. The solvent would get into the connector coupling portion resulting deteriorated
characteristics. Should it be necessary to remove the flux, please use one of the following solvents only to be applied with
a brush.
Solvent : Isopropyl alcohol, Methyl alcohol
(5) Ground during assembling
The human body and the soldering iron must be grounded against the static breakdown of the device during assembling.
Please avoid touching the device terminals as much as possible before assembling.
(6) Assembly of the device
Please fix this device with a screw. In case that this device is not fixed with a screw, stress by detaching connector of
internal elements and leads can adversely affect the device’s reliability. Excessive torque can deform the package and
damage the optics. It can also adversely affect the device’s reliability because the device is used under continuous stress.
Please confirm the limit of fixing torque to the installation before fixing actually.
Recommended values
Screw : M3.0 × 8 mm tapping screw
Fixing torque : 0.7 to 0.8 N·m
Force applied by driver etc. : 39 N or less
Note : Please contact and consult with a Sharp sales representative for any questions about above.
(7) Input signal
This product is designed intentionally based upon the signal transmission which is defined by the digital audio interface
standard ; CP1201. When a signal out of JEITA standard CP-1201 is inputted to this device, there might be a case that this
device can not transmit a signal correctly to receiving unit.
(8) Fixing pin
Since there are other products which has a different fixing pin shape, please make sure to confirm reference mounting
drawing for this device.
(9) Damage to connector coupling portion
Please do not stress the connector coupling portion excessively since there might be a case that the shutter can’t operate
normally.
www(1.0D)aAtabSohuPtelgeetea4tstUein.agcvotohmied
flux into
getting a
connector coupling
flux into connector
portion
coupling
portion
of
this
device,
because
there
might
be
a
case
that
the
characteristics
deteriorate the shutter can’t operate normally.
Sheet No.: E2-A00601EN
6

6 Page







SeitenGesamt 8 Seiten
PDF Download[ GP1FAV31TK0F Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
GP1FAV31TK0FFiber Optic Transmitter Square connectorSharp Electrionic Components
Sharp Electrionic Components

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche