Datenblatt-pdf.com


CFD-G700CP Schematic ( PDF Datasheet ) - Sony

Teilenummer CFD-G700CP
Beschreibung CD RADIO CASSETTE-CORDER
Hersteller Sony
Logo Sony Logo 




Gesamt 30 Seiten
CFD-G700CP Datasheet, Funktion
SERVICE MANUAL
Ver. 1.0 2007.03
CFD-G700CP/G770CP/
G770CPKwww.DataSheet4U.com
US Model
CFD-G700CP
Canadian Model
CFD-G770CPK
E Model
CFD-G770CP/G770CPK
Australian Model
CFD-G770CPK
Photo : CFD-G770CPK
CD
Section
TAPE
Section
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Type
Model Name Using Similar Mechanism
Tape Transport Mechanism Type
CFD-G505/G555CP/G555CPK
KSM-213CDP/C2NP
KSS-213C
HCD-EC50
H21SB-C05
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 3.2-ohm loads, both channels driven from
1 000 - 10 000 Hz; rated 3 W per channel-minimum
RMS power, with no more than 10 % total harmonic
distortion in AC operation.
Woofer with 4-ohm loads, driven from 50 - 150
Hz; rated 6 W minimum RMS power, with no more
than 10 % total harmonic distortion in AC
operation.
Other specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW
(Th is output is the value measured at a distance
of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and fl utter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1 710 kHz
(G700CP: US/G770CPK: CND, MX, E92)
AM: 531 - 1 611 kHz (G770CPK: AUS)
AM: 531 - 1 611 kHz (9 kHz step)(G770CP)
AM: 530 - 1 610 kHz (10 kHz step)(G770CP)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 150 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
General
Speaker
Full range: 10 cm (4 in.) dia., 3.2 ,
cone type (2)
Woofer: 13 cm (5 1/8 in.) dia., 4 ,
cone type (1)
Tweeter: 2 cm (13/16 in.) dia. (2)
Input
Built-in audio cable with stereo-mini plug:
Minimum input level 245 mV
AUDIO IN Jack (stereo minijack):
Minimum input level 245 mV
MIC MIX (microphone) jack (monaural minijack):
Sensitivity 2.5 mV, for low impedance
microphone
Minimum input level 2.5 mV (G770CPK)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 impedance headphones
Power output
4 W + 4 W (at 3.2 , 10% harmonic distortion)
Woofer:
12 W (at 4 , 10% harmonic distortion)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz
(G700CP: US/G770CPK: CND, MX, E92)
230 - 240 V AC, 50 Hz (G700CP: SP)
230 V AC, 50 Hz
(G700CP: E41/G770CPK: AUS)
12 V DC, 8 R20 (size D) batteries
For remote control:
3 V DC, 2 R6 (size AA) batteries
Power consumption
AC 28 W
— Continued on next page —
• Abbreviation
AUS : Australian model
E92 : AC 120V area in E model
CND : Canadian model
MX : Mexican model
E41 : AC 230V area in E model SP : Singapore model
CD RADIO CASSETTE-CORDER
9-887-620-01
2007C16-1
© 2007.03
Sony Corporation
Personal Audio Division
Published by Sony Techno Create Corporation






CFD-G700CP Datasheet, Funktion
CFD-G700CP/G770CP/G770CPK
www.DataSheet4U.com
CFD-G700CP (2/2)
Other Operations
Using the display
You can check information about the CD using the
display.
Checking the information of an audio CD
To check the total track number and playing
time of the CD
Press Ą Ȱ while the CD is stopped, and you can check
them in the display.
Total track number
Total playing time
Checking the information of an MP3 disc
To check the total folder number and total file
number on the CD
Press Ą Ȱ while the CD is stopped, and you can check
them in the display.
Total file number
Total folder number
To check file information
Press DSPL/ENT Ȼ on the unit while playing an MP3
disc. The display changes as follows:
Ô The current file number and playing time
€
The song title ( )
€
The artist name ( )
€
The album name ( )
Playing tracks/MP3 files repeatedly
(Repeat Play)
You can play tracks/MP3 files repeatedly in normal,
Shuffle or Program play modes.
1 Press Ą Ȱ.
“CD” appears in the display.
2 Proceed as follows.
To repeat Do this
A single
track/MP3
file
1 Press REPEAT ȵ until “ 1” appears.
2 Press à or Ñ ȯ to select the track/
MP3 file that you want to repeat.
3 Press ā Ȱ on the unit.
All tracks/ 1 Press REPEAT ȵ until “ ” appears.
MP3 files 2 Press ā Ȱ on the unit.
on the CD
A selected
folder
(MP3 disc
only)
1 Press MODE ȶ until “ ” appears,
and then press REPEAT ȵ until “ ”
appears.
2 Select the folder by pressing + or
Ȯ.
3 Press ā Ȱ on the unit.
Tracks/
MP3 files
in random
order
1 Select Shuffle Play (see “Playing tracks/
MP3 files in random order”).
2 Press REPEAT ȵ until “SHUF” and
“ ” appear.
3 Press ā Ȱ on the unit.
Files in a 1 Start Folder Shufle Play (see “Playing
selected
tracks/MP3 files in random order”).
folder in 2 Press REPEAT ȵ on the unit until “
random
“SHUF” and “ ” appear.
order (MP3 3 Press ā Ȱ on the unit.
disc only)
”,
Programed 1 Program tracks/MP3 files (see “Creating
tracks/MP3 your own program”).
files 2 Press REPEAT ȵ until “ ” and “PGM”
appear.
3 Press ā Ȱ on the unit.
On the remote
Use à Ȱ instead of ā Ȱ.
To cancel Repeat Play
Press REPEAT ȵ until “ ” disappears from the display.
Playing tracks/MP3 files in random
order (Shuffle Play)
You can play tracks/MP3 files in random order. When
playing an MP3 disc, you can also play MP3 files in a
selected folder in random order (Folder Shuffle Play).
1 Press Ą Ȱ.
“CD” appears in the display.
2 Press MODE ȶ until “SHUF” appears in the display.
When you select Folder Shuffle Play (MP3 disc only),
press MODE ȶ on the unit until “ ” and “SHUF”
appear in the display. Then press TUNE + or – Ȯ
on the unit to select a folder you want.
3 Press ā Ȱ on the unit to start Shuffle Play.
On the remote
Use à Ȱ instead of ā Ȱ.
To cancel Shuffle Play
Stop playing first. Then press MODE ȶ until “SHUF”
disappears from the display.
Tips
ˎ During Shuffle Play, you cannot select the previous track/MP3 file by
pressing à ȯ.
ˎ The resume function does not work during Shuffle Play.
Creating your own program (Program
Play)
You can arrange the playing order of up to 15 tracks/MP3
files on a CD.
1 Press Ą Ȱ.
“CD” appears in the display.
2 Press MODE ȶ until “PGM” flashes in the display.
3 Press à or Ñ ȯ then press DSPL/ENT Ȼ on the
unit (ENTER Ɂ on the remote) for the tracks/MP3
files you want to program in the order you want.
For MP3 files, press TUNE + or – Ȯ first and then
press à or Ñ ȯ and DSPL/ENT Ȼ (ENTER Ɂ
on the remote).
Audio CD (Program Play)
Programed track number
Playing order
MP3 disc (Program Play)
Programed file number
Playing order
4 Press ā Ȱ on the unit to start Program Play.
On the remote
Use à Ȱ instead of ā Ȱ.
To cancel Program Play
Stop playing first. Then press MODE ȶ until “PGM”
disappears from the display.
To delete the last track or file of the program
Press CLEAR ȿ on the remote while the unit is stopped.
To check the order of tracks/MP3 files before
play
Press DSPL/ENT Ȼ on the unit.
Every time you press the button, the track number and
the playing order appear.
To change the current program
Press Ą Ȱ once if the CD is stopped and twice if the
CD is playing. The current program will be erased.
Then create a new program following the programing
procedure.
Tips
ˎ If you try to program 16 tracks/MP3 files or more, “FULL” will
appear in the display.
ˎ You can play the same program again, since the program is saved
until you open the CD compartment or turn off the power of the
unit.
ˎ You can record your own program. After you have created the
program, insert a blank tape and press Ć Ȫ on the unit to start
recording.
ˎ The resume function does not work during Program Play.
Presetting radio stations
You can store radio stations into the unit’s memory. You
can preset up to 30 radio stations, 20 for FM and 10 for
AM in any order.
1 Press RADIO/BANDˎAUTO PRESET ȭ on the unit to
select the band.
2 Hold down RADIO/BANDˎAUTO PRESET ȭ on the
unit for 2 seconds until “AUTO” flashes in the display.
3 Press DSPL/ENT Ȼ on the unit.
The stations are stored in memory from the lower
frequencies to the higher ones.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
1 Press RADIO/BANDˎAUTO PRESET ȭ on the unit to
select the band.
2 Tune in a station you want.
3 Hold down DSPL/ENT Ȼ on the unit for 2 seconds
until the preset number flashes in the display.
4 Press PRESET + or – ȯ on the unit until the preset
number you want for the station flashes in the
display.
5 Press DSPL/ENT Ȼ on the unit.
The new station replaces the old one.
On the remote
1 Press RADIO/BAND ȭ until the band you want
appears in the display.
2 Tune in a station you want.
3 Hold down ENTER Ɂ for 2 seconds until the preset
number flashes in the display.
4 Press PRESET + or – ȯ until the preset number you
want for the station flashes in the display.
5 Press ENTER Ɂ.
Tip
The preset radio stations remain in memory even if you unplug the
AC power cord or remove the batteries.
Playing preset radio stations
1 Press RADIO/BANDˎAUTO PRESET ȭ on the unit to
select the band.
2 Press PRESET + or – ȯ on the unit to tune in the
stored station.
On the remote
1 Press RADIO/BAND ȭ.
2 Press PRESET + or – ȯ to tune in the stored station.
Falling asleep to music
1 Play the music source you want.
2 Press SLEEP Ⱥ to display “SLEEP”.
3 Press SLEEP Ⱥ to select the minutes until the unit
goes off automatically.
Each time you press the button, the indication changes
as follows:
“AUTO*” ‚ “60MIN” ‚ “30MIN” ‚ “20MIN” ‚
“10MIN” ‚ “OFF”.
* When you select “AUTO”, the CD or tape stops playing in 90
minutes at most and the unit goes off automatically. When you
are listening to the radio, the radio goes off in 90 minutes.
If 4 seconds have passed after you pressed SLEEP Ⱥ,
the minutes in the display are entered.
When the preset time has passed, the unit goes off
automatically.
To cancel the sleep function
Press POWER ȩ to turn off the power.
Note
When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the unit will
not go off until the tape reaches the end.
Connecting optional component
You can enjoy the sound from an optional component
such as a portable digital music player through the
speakers of this unit.
Be sure to turn off the power of each component before
making any connections.
For details, refer to the instruction manual of the
component to be connected.
To AUDIO IN jack
Built-in audio cable
with stereo-mini plug or
audio connecting
cable (not supplied)
To the line output jack
(e.g.,portable digital
music player)
1 Connect the built-in audio cable with stereo-mini
plug ȴ on the unit to the line output jack of the
portable digital music player or other components*.
2 Turn the unit and the connected component on.
3 Press AUDIO IN ȶ on the unit and start playing
sound on the connected component.
The sound from the connected component is output
from the speakers.
* To connect the unit to a TV or VCR, use an extension cable (not
supplied) with a stereo-mini jack on one end (for the built-in audio
cable) and two phono plugs on the other end.
Recording the sound from the connected
component
1 Insert a blank tape.
2 Press AUDIO IN ȶ on the unit to display “AUDIO IN”.
3 Press Ć Ȫ on the unit.
Recording starts.
4 Play the optional component connected to the unit.
Tip
Should the built-in audio cable ȴ become damaged, you can use the
AUDIO IN jack ȳ to connect an optional component to the unit. Use
an audio connecting cable (not supplied) with a stereo mini plug on
one end (for the AUDIO IN jack ȳ). Make sure the plug on the other
end is suited to the jack on the optional component; for example, a
stereo-mini plug for a portable digital music player, or two phono
plugs for a TV or VCR.
Notes
ˎ Do not pull forcibly on the built-in audio cable ȴ. Doing so may
cause the plug to rip off.
ˎ Connect the built-in audio cable ȴ or audio connecting cable (not
supplied) securely to prevent any malfunction.
ˎ It is not possible to listen to two components connected at the same
time through the built-in audio cable ȴ and the AUDIO IN jack ȳ
(using an optional audio connecting cable). Connect one component
at a time.
D-LIGHT SYNC OUT jack
Use the D-LIGHT SYNC controller to connect to this
D-LIGHT SYNC OUT jack ȫ. You need to connect
the D-LIGHT SYNC controller to the lighting device*
(not supplied). The lighting device will react according
to control signals transmitted by the D-LIGHT SYNC
controller upon receiving music source from the system.
For details on the use of D-LIGHT SYNC controller
and lighting device, refer to the respective operating
instructions supplied with the respective device.
D-LIGHT SYNC controller cord of
D-LIGHT SYNC controller (DSL-1)
* Refer to the D-LIGHT SYNC controller operating instruction for the
recommended lighting device.
Note
The lighting effect may be different depending on the connected
lighting device or the type of music being played back.
6

6 Page









CFD-G700CP pdf, datenblatt
CFD-G700CP/G770CP/G770CPK
Note: Follow the disassembly procedure in the numerical order given.
3-2. CABINET (UPPER) (1) SECTION
6 three screws
(+BV tapping (B3))
4 two screws
(+BV tapping (B3))
www.DataSheet4U.com
1 Open the handle in the
direction of the arrow.
2 four screws
(+BV tapping (B3))
3 Open the cassette lid.
5 Open the CD lid.
3-3. CABINET (UPPER) (2) SECTION
qj handle
5 CNP391 (5P)
6 CNP301 (5P)
7 CNP393 (4P)
8 CNP390 (6P)
(G770CPK)
9 flexible flat cable
(19core) (CN803)
q; flexible flat cable
(19core) (CN804)
qf CNP394 (3P)
qd CNP803 (2P)
qs CNP806 (2P)
qa CNP807 (2P)
1 Close the cassette lid.
3 qh cabinet (upper)
section
qg CNP391 (5P)
2 Close the CD lid.
4 Open the cabinet (upper) section.
12

12 Page





SeitenGesamt 30 Seiten
PDF Download[ CFD-G700CP Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
CFD-G700CPCD RADIO CASSETTE-CORDERSony
Sony

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche