Datenblatt-pdf.com


EBE11ED8AGFA Schematic ( PDF Datasheet ) - Elpida Memory

Teilenummer EBE11ED8AGFA
Beschreibung 1GB Unbuffered DDR2 SDRAM DIMM
Hersteller Elpida Memory
Logo Elpida Memory Logo 




Gesamt 23 Seiten
EBE11ED8AGFA Datasheet, Funktion
DATA SHEET
www.DataSheet4U.com
1GB Unbuffered DDR2 SDRAM DIMM
EBE11ED8AGFA (128M words × 72 bits, 2 Ranks)
Description
The EBE11ED8AGFA is 128M words × 72 bits, 2 ranks
DDR2 SDRAM unbuffered module, mounting 18 pieces
of 512M bits DDR2 SDRAM sealed in FBGA (µBGA)
package. Read and write operations are performed at
the cross points of the CK and the /CK. This high-
speed data transfer is realized by the 4 bits prefetch-
pipelined architecture. Data strobe (DQS and /DQS)
both for read and write are available for high speed and
reliable data bus design. By setting extended mode
register, the on-chip Delay Locked Loop (DLL) can be
set enable or disable. This module provides high
density mounting without utilizing surface mount
technology. Decoupling capacitors are mounted
beside each FBGA (µBGA) on the module board.
Note: Do not push the components or drop the
modules in order to avoid mechanical defects,
which may result in electrical defects.
Features
240-pin socket type dual in line memory module
(DIMM)
PCB height: 30.0mm
Lead pitch: 1.0mm
Lead-free (RoHS compliant)
Power supply: VDD = 1.8V ± 0.1V
Data rate: 667Mbps/533Mbps/400Mbps (max.)
SSTL_18 compatible I/O
Double-data-rate architecture: two data transfers per
clock cycle
Bi-directional, differential data strobe (DQS and
/DQS) is transmitted/received with data, to be used in
capturing data at the receiver
DQS is edge aligned with data for READs: center-
aligned with data for WRITEs
Differential clock inputs (CK and /CK)
DLL aligns DQ and DQS transitions with CK
transitions
Commands entered on each positive CK edge: data
and data mask referenced to both edges of DQS
Four internal banks for concurrent operation
(components)
Data mask (DM) for write data
Burst lengths: 4, 8
/CAS Latency (CL): 3, 4, 5
Auto precharge operation for each burst access
Auto refresh and self refresh modes
Average refresh period
7.8µs at 0°C TC ≤ +85°C
3.9µs at +85°C < TC ≤ +95°C
Posted CAS by programmable additive latency for
better command and data bus efficiency
Off-Chip-Driver Impedance Adjustment and On-Die-
Termination for better signal quality
/DQS can be disabled for single-ended Data Strobe
operation
Document No. E0784E20 (Ver. 2.0)
Date Published October 2005 (K) Japan
Printed in Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2005






EBE11ED8AGFA Datasheet, Funktion
EBE11ED8AGFA
www.DataSheet4U.com
Byte No. Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value Comments
29
Minimum /RAS to /CAS delay (tRCD) 0 0 1 1 1 1 0 0 3CH
15ns
Minimum active to precharge time
30 (tRAS)
0 0 1 0 1 1 0 1 2DH
45ns
-6E, -5C
-4A
0 0 1 0 1 0 0 0 28H
40ns
31 Module rank density
1 0 0 0 0 0 0 0 80H
Address and command setup time
32 before clock (tIS)
0 0 1 0 0 0 0 0 20H
-6E
-5C 0 0 1 0 0 1 0 1 25H
-4A 0 0 1 1 0 1 0 1 35H
Address and command hold time
33 after clock (tIH)
0 0 1 0 1 0 0 0 28H
-6E
-5C 0 0 1 1 1 0 0 0 38H
-4A 0 1 0 0 1 0 0 0 48H
Data input setup time before clock
34 (tDS)
0 0 0 1 0 0 0 0 10H
-6E, -5C
-4A 0 0 0 1 0 1 0 1 15H
35
Data input hold time after clock (tDH)
-6E
0
0
0
1
1
0
0
0
18H
-5C 0 0 1 0 0 0 1 1 23H
-4A 0 0 1 0 1 0 0 0 28H
36 Write recovery time (tWR)
0 0 1 1 1 1 0 0 3CH
Internal write to read command delay
37 (tWTR)
0 0 0 1 1 1 1 0 1EH
-6E, -5C
-4A 0 0 1 0 1 0 0 0 28H
38
Internal read to precharge command
delay (tRTP)
0
0
0
1
1
1
1
0
1EH
39
Memory analysis probe
characteristics
0 0 0 0 0 0 0 0 00H
40 Extension of Byte 41 and 42
0 0 0 0 0 0 0 0 00H
41
Active command period (tRC)
-6E, -5C
0 0 1 1 1 1 0 0 3CH
-4A 0 0 1 1 0 1 1 1 37H
42
Auto refresh to active/
Auto refresh command cycle (tRFC)
0
1
1
0
1
0
0
1
69H
43 SDRAM tCK cycle max. (tCK max.) 1 0 0 0 0 0 0 0 80H
44
Dout to DQS skew
-6E
0 0 0 1 1 0 0 0 18H
-5C 0 0 0 1 1 1 1 0 1EH
-4A
45
Data hold skew (tQHS)
-6E
-5C
0 0 1 0 0 0 1 1 23H
0 0 1 0 0 0 1 0 22H
0 0 1 0 1 0 0 0 28H
-4A 0 0 1 0 1 1 0 1 2DH
46 PLL relock time
0 0 0 0 0 0 0 0 00H
47 to 61
0 0 0 0 0 0 0 0 00H
512M bytes
0.20ns*1
0.25ns*1
0.35ns*1
0.28ns*1
0.38ns*1
0.48ns*1
0.10ns*1
0.15ns*1
0.18ns*1
0.23ns*1
0.28ns*1
15ns*1
7.5ns*1
10ns*1
7.5ns*1
TBD
Undefined
60ns*1
55ns*1
105ns*1
8ns*1
0.24ns*1
0.30ns*1
0.35ns*1
0.34ns*1
0.40ns*1
0.45ns*1
Undefined
Data Sheet E0784E20 (Ver. 2.0)
6

6 Page









EBE11ED8AGFA pdf, datenblatt
EBE11ED8AGFA
www.DataSheet4U.com
Parameter
Symbol Grade max.
Unit Test condition
Self-refresh current
IDD6
Self Refresh Mode;
CK and /CK at 0V;
108 mA CKE 0.2V;
Other control and address bus inputs are FLOATING;
Data bus inputs are FLOATING
Operating current
(Bank interleaving)
IDD7
(Another rank is in IDD2P)
Operating current
(Bank interleaving)
IDD7
(Another rank is in IDD3N)
-6E
-5C
-4A
-6E
-5C
-4A
2970
2970
2772
3510
3465
3240
all bank interleaving reads, IOUT = 0mA;
mA BL = 4, CL = CL(IDD), AL = tRCD (IDD) 1 × tCK (IDD);
tCK = tCK (IDD), tRC = tRC (IDD), tRRD = tRRD(IDD),
tRCD = 1 × tCK (IDD);
CKE is H, CS is H between valid commands;
mA Address bus inputs are STABLE during DESELECTs;
Data pattern is same as IDD4W;
Notes: 1. IDD specifications are tested after the device is properly initialized.
2. Input slew rate is specified by AC Input Test Condition.
3. IDD parameters are specified with ODT disabled.
4. Data bus consists of DQ, DM, DQS, /DQS, RDQS, /RDQS, LDQS, /LDQS, UDQS, and /UDQS. IDD
values must be met with all combinations of EMRS bits 10 and 11.
5. Definitions for IDD
L is defined as VIN VIL (AC) (max.)
H is defined as VIN VIH (AC) (min.)
STABLE is defined as inputs stable at an H or L level
FLOATING is defined as inputs at VREF = VDDQ/2
SWITCHING is defined as:
inputs changing between H and L every other clock cycle (once per two clocks) for address and control
signals, and inputs changing between H and L every other data transfer (once per clock) for DQ signals
not including masks or strobes.
6. Refer to AC Timing for IDD Test Conditions.
AC Timing for IDD Test Conditions
For purposes of IDD testing, the following parameters are to be utilized.
DDR2-667
DDR2-533
Parameter
5-5-5
4-4-4
CL(IDD)
54
tRCD(IDD)
15 15
tRC(IDD)
60 60
tRRD(IDD)
7.5 7.5
tCK(IDD)
3 3.75
tRAS(min.)(IDD)
45 45
tRAS(max.)(IDD)
70000
70000
tRP(IDD)
15 15
tRFC(IDD)
105 105
DDR2-400
3-3-3
3
15
55
7.5
5
40
70000
15
105
Unit
tCK
ns
ns
ns
ns
ns
ns
ns
ns
Data Sheet E0784E20 (Ver. 2.0)
12

12 Page





SeitenGesamt 23 Seiten
PDF Download[ EBE11ED8AGFA Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
EBE11ED8AGFA1GB Unbuffered DDR2 SDRAM DIMMElpida Memory
Elpida Memory

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche