PCA9306 Datasheet PDF - NXP Semiconductors
| Part Number | PCA9306 | |
| Description | Dual bidirectional I2C-bus and SMBus voltage-level translator | |
| Manufacturers | NXP Semiconductors | |
| Logo |  |
|
|
There is a preview and PCA9306 download ( pdf file ) link at the bottom of this page. Total 23 Pages | ||
Preview 1 page No Preview Available !
PCA9306
Dual bidirectional I2C-bus and SMBus voltage-level translator
Rev. 04 — 26 October 2009
Product data sheet
1. General description
www.DataSheet4U.com
The PCA9306 is a dual bidirectional I2C-bus and SMBus voltage-level translator with an
enable (EN) input, and is operational from 1.0 V to 3.6 V (Vref(1)) and 1.8 V to 5.5 V
(Vbias(ref)(2)).
The PCA9306 allows bidirectional voltage translations between 1.0 V and 5 V without the
use of a direction pin. The low ON-state resistance (Ron) of the switch allows connections
to be made with minimal propagation delay. When EN is HIGH, the translator switch is on,
and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively,
allowing bidirectional data flow between ports. When EN is LOW, the translator switch is
off, and a high-impedance state exists between ports.
The PCA9306 is not a bus buffer like the PCA9509 or PCA9517A that provide both level
translation and physically isolates the capacitance to either side of the bus when both
sides are connected. The PCA9306 only isolates both sides when the device is disabled
and provides voltage level translation when active.
The PCA9306 can also be used to run two buses, one at 400 kHz operating frequency
and the other at 100 kHz operating frequency. If the two buses are operating at different
frequencies, the 100 kHz bus must be isolated when the 400 kHz operation of the other
bus is required. If the master is running at 400 kHz, the maximum system operating
frequency may be less than 400 kHz because of the delays added by the translator.
As with the standard I2C-bus system, pull-up resistors are required to provide the logic
HIGH levels on the translator’s bus. The PCA9306 has a standard open-collector
configuration of the I2C-bus. The size of these pull-up resistors depends on the system,
but each side of the translator must have a pull-up resistor. The device is designed to work
with Standard-mode, Fast-mode and Fast mode Plus I2C-bus devices in addition to
SMBus devices. The maximum frequency is dependent on the RC time constant, but
generally supports > 2 MHz.
When the SDA1 or SDA2 port is LOW, the clamp is in the ON-state and a low resistance
connection exists between the SDA1 and SDA2 ports. Assuming the higher voltage is on
the SDA2 port when the SDA2 port is HIGH, the voltage on the SDA1 port is limited to the
voltage set by VREF1. When the SDA1 port is HIGH, the SDA2 port is pulled to the drain
pull-up supply voltage (Vpu(D)) by the pull-up resistors. This functionality allows a seamless
translation between higher and lower voltages selected by the user without the need for
directional control. The SCL1/SCL2 channel also functions as the SDA1/SDA2 channel.
All channels have the same electrical characteristics and there is minimal deviation from
one output to another in voltage or propagation delay. This is a benefit over discrete
transistor voltage translation solutions, since the fabrication of the switch is symmetrical.
The translator provides excellent ESD protection to lower voltage devices, and at the
same time protects less ESD-resistant devices.
|
| |
 
NXP Semiconductors
PCA9306
Dual bidirectional I2C-bus and SMBus voltage-level translator
5.2 Pin description
Table 2.
Symbol
GND
VREF1
SCL1
SDA1
SDA2
SCL2
VREF2
EN
Pin description
Pin
SO8,
VSSOP8 (DC)
TSSOP8 (MSOP8),
TSSOP8,
VSSOP8 (DC1),
XQFN8
14
21
32
43
55
66
77
88
Description
ground (0 V)
low-voltage side reference supply voltage for
SCL1 and SDA1
serial clock, low-voltage side; connect to
VREF1 through a pull-up resistor
serial data, low-voltage side; connect to VREF1
through a pull-up resistor
serial data, high-voltage side; connect to
VREF2 through a pull-up resistor
serial clock, high-voltage side; connect to
VREF2 through a pull-up resistor
high-voltage side reference supply voltage for
SCL2 and SDA2
switch enable input; connect to VREF2 and
pull-up through a high resistor
www.DataSheet4U.com
PCA9306_4
Product data sheet
Rev. 04 — 26 October 2009
© NXP B.V. 2009. All rights reserved.
5 of 23
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for PCA9306 electronic component. |
| Information | Total 23 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ PCA9306.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| PCA9306 | The function is PCA9306 Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator (Rev. L). Texas Instruments |  |
| PCA9306 | The function is Dual bidirectional I2C-bus and SMBus voltage-level translator. NXP Semiconductors | |
| PCA9306 | The function is Dual Bidirectional I2C-bus and SMBus Voltage-Level Translator. ON Semiconductor |  |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
PCA9
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||