|
|
Número de pieza | ENT1 | |
Descripción | 12.5kHz Channel VHF High Power TX | |
Fabricantes | Radiometrix | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ENT1 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
No Preview Available ! NEW Radiometrix
Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England
Issue 1, 16 October 2007
Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233
ENT1
12.5kHz Channel VHF High Power TX
The ENT1 transmitter modules offer a
100mW RF output VHF data link in
Radiometrix SIL standard pin-out and
footprint. This makes the ENT1 ideally
suited to those low power applications
where existing narrow band and
wideband transmitters provide
insufficient range. Together with the
matching LMR1/RX1M receiver a one-
way radio data link can be achieved
over a distance up to 10km+ with
suitable choice of data rate and
antennas.
Figure 1: ENTI –169.40625-3
Features
• Conforms to EN 300 220-3 and EN 301 489-3
• Standard frequency 169.406250MHz
• Other frequencies from 120MHz to 180MHz
• 12.5 kHz channel spacing
• Data rates up to 3kbps
• Usable range over 10km
• Fully screened
• Low power requirements
Applications
www.DataSheet4U.com
• Remote meter reading
• Data loggers
• Industrial telemetry and telecommand
• In-building environmental monitoring and control
• High-end security and fire alarms
• DGPS systems
• Vehicle data up/download
Technical Summary
• Size: 43 x 14.5 x 5mm
• Operating frequency: 169.406250MHz
• Supply range: 5v
• Current consumption: 70mA Max
• Data bit rate: 3kbps max.
• Transmit power: 20dBm (100mW) nominal
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 1
1 page Applications information
Power supply requirements
The ENT1 has a built-in regulator which delivers a constant 3.3V to the transmitter frequency control
circuitry when the external supply voltage is 3.4V or greater. This ensures constant frequency stability
and removes the need for external supply decoupling except in cases where the supply rail is extremely
poor (ripple/noise content >0.1Vp-p).
TX modulation requirements
The module is factory-set to produce the specified FM deviation with a TXD input to pin 14 of 5V
amplitude, i.e. 0V “low”, 5V “high
If the data input level is greater than 5V, a resistor must be added in series with the TXD input to limit
the modulating input voltage to a maximum of 5V on pin 7. TXD input resistance is 100kΩ to ground.
Expected range
Predicting the range obtainable in any given situation is notoriously difficult since there are many
factors involved. The main ones to consider are as follows:
• Type and location of antennas in use
• Type of terrain and degree of obstruction of the link path
• Sources of interference affecting the receiver
• “Dead” spots caused by signal reflections from nearby conductive objects
• Data rate and degree of filtering employed
The following are typical examples – but range tests should always be performed before assuming that
a particular range can be achieved in a given situation:
Data rate
1.2kbps
Tx antenna
half-wave
Rx antenna
half-wave
Environment
rural/open
Range
10-15km
Note: The figure for 1.2kbps assumes that the receiver bandwidth has been suitably reduced by
utilising an outboard sallen-key active audio filter and data slicer or similar arrangement.
www.DataSheet4U.com
The ENT1’s TXD input is normally driven directly by logic levels but will also accept analogue drive
(e.g. 2-tone signalling). In this case it is recommended that TXD (pin 14) be DC-biased to 2.5V approx.
with the modulation ac-coupled and limited to a maximum of 5Vp-p to minimise distortion over the link.
Although the modulation bandwidth of the ENT1 extends down to DC it is not advisable to use data
containing a DC component. This is because frequency errors and drifts between the transmitter and
receiver occur in normal operation, resulting in DC offset errors on the receiver’s audio output.
Radiometrix Ltd.,
ENT1 high power transmitter data sheet
Page 5
5 Page Radiometrix Ltd
Hartcran House
231 Kenton Lane
Harrow, Middlesex
HA3 8RP
ENGLAND
Tel: +44 (0) 20 8909 9595
Fax: +44 (0) 20 8909 2233
www.radiometrix.com
Copyright notice
This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or in
part must give clear acknowledgement to the copyright owner.
Limitation of liability
The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the
right to make changes or improvements in the design, specification or manufacture of its subassembly products without
notice. Radiometrix Ltd does not assume any liability arising from the application or use of any product or circuit
described herein, nor for any infringements of patents or other rights of third parties which may result from the use of
its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular
application. These radio devices may be subject to radio interference and may not function as intended if interference is
present. We do NOT recommend their use for life critical applications.
The Intrastat commodity code for all our modules is: 8542 6000
R&TTE Directive
After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of the R&TTE
Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance to the essential
requirements specified in Article 3 of the Directive, as appropriate to the particular equipment.
Further details are available on The Office of Communications (Ofcom) web site:
http://www.ofcom.org.uk/radiocomms/ifi/
www.DataSheIent4foUr.cmoamtion Requests
Ofcom
Riverside House
2a Southwark Bridge Road
London SE1 9HA
Tel: +44 (0)845 456 3000 or 020 7981 3040
Fax: +44 (0)20 7783 4033
European Radiocommunications Office (ERO)
Peblingehus
Nansensgade 19
DK 1366 Copenhagen
Tel. +45 33896300
Fax +45 33896330
www.ero.dk
11 Page |
Páginas | Total 11 Páginas | |
PDF Descargar | [ Datasheet ENT1.PDF ] |
Número de pieza | Descripción | Fabricantes |
ENT1 | 12.5kHz Channel VHF High Power TX | Radiometrix |
ENT1D-449-Y00064 | Rotary Optical Encoder | Bourns |
ENT1D-467-Y00064 | Rotary Optical Encoder | Bourns |
ENT1D-D16-L00256 | Rotary Optical Encoder | Bourns |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |