Datenblatt-pdf.com


AAT2860 Schematic ( PDF Datasheet ) - Advanced Analogic Technologies

Teilenummer AAT2860
Beschreibung Backlight/Flash LED Driver and Multiple LDO Lighting Management Unit
Hersteller Advanced Analogic Technologies
Logo Advanced Analogic Technologies Logo 




Gesamt 23 Seiten
AAT2860 Datasheet, Funktion
www.DataSheet4U.com
ChargePumpTM
PRODUCT DATASHEET
AAT2860
Backlight/Flash LED Driver and Multiple LDO Lighting Management Unit
General Description
The AAT2860-x is a highly integrated charge pump-based
lighting management unit (LMU) with three low dropout
(LDO) regulators optimized for single-cell lithium-ion/
polymer systems. The charge pump provides power for
all LED outputs; multiple backlight and flash LED configu-
rations are available. The backlight LED outputs can be
programmed up to 31mA each and the flash LED outputs
can be programmed up to 300mA each. An I2C compati-
ble serial digital interface is used to enable, disable, and
set the current to one of 32 levels for the backlight and
one of 16 levels for the flash. A programmable safety
timer and flash control input is included for easy flash
control. Backlight current matching is better than 3% for
uniform display brightness, and flash current matching is
better than 5% for uniform power dissipation.
The AAT2860-x offers three high-performance low-noise
MicroPower™ LDO linear regulators. The regulators are
enabled and their output voltages are set through the
I2C compatible serial interface. Each LDO can supply up
to 300mA load current and ground-pin current is only
80µA making the AAT2860-x ideal for battery-operated
applications.
The AAT2860-x is available in a Pb-free, space saving
TQFN34-24 package and operates over the -40°C to
+85°C ambient temperature range.
Features
• Input Voltage Range: 2.7V to 5.5V
I2C Compatible Serial Interface
• Tri-Mode Charge Pump
Drives up to Seven LEDs (Backlight/Flash)
• Programmable Backlight Current Settings
32 Levels - 0.5mA to 31mA
• Programmable Flash Current
16 Levels – OFF to 300mA
• 1MHz Switching Frequency
• Automatic Soft-Start
• Three Low Dropout Regulators
300mA Output Current
150mV Dropout
Programmable Output from 1.5V to 3.0V
Output Auto-Discharge for Fast Shutdown
• Built-In Thermal Protection
• -40°C to +85°C Temperature Range
• TQFN34-24 Package
Applications
• Camera Enabled Mobile Devices
• Digital Still Cameras
• Multimedia Mobile Phones
Typical Application
VBAT
3.6V
CIN
4.7µF
CIN
4.7µF
LED Select
Flash Level Select
I2C Serial SDA
Interface
SCL
LDO Select
C1 C2
1µF 1µF
C1+ C1- C2+ C2-
IN OUT
AAT2860-x
IN
LED_SEL
FL_LVL
SDA
SCL
BL1
BL2
BL3
BL4
BL5
BL6/FL1
BL7/FL2
LDOA
LDO_SEL LDOB
AGND
LDOC
PGND
WLEDs
OSRAM LW M673
or equivalent
VOUT
COUT
2.2µF
Flash LEDs
Lumiled LXCL-PWF1
or equivalent
VLDOC
at 300mA
CLDOC
2.2µF
VLDOB
at 300mA
CLDOB
2.2µF
VLDOA
at 300mA
CLDOA
2.2µF
2860.2008.05.1.0
www.analogictech.com
1






AAT2860 Datasheet, Funktion
www.DataSheet4U.com
ChargePumpTM
PRODUCT DATASHEET
AAT2860
Backlight/Flash LED Driver and Multiple LDO Lighting Management Unit
I2C Compatible Interface Timing Details
tt
t tt
t
t
t
t
6
www.analogictech.com
2860.2008.05.1.0

6 Page









AAT2860 pdf, datenblatt
www.DataSheet4U.com
ChargePumpTM
PRODUCT DATASHEET
AAT2860
Backlight/Flash LED Driver and Multiple LDO Lighting Management Unit
the LED off, the safety timer insures that the LED or
other circuitry is not damaged.
Both the backlight and flash LED currents are programmed
through the I2C compatible serial interface as are the
backlight fade timer, the flash safety timer, and the torch/
flash inhibit current levels. See the “I2C Compatible Serial
Interface” section of this datasheet for more information
on setting the LED currents. To enable the flash LED(s),
strobe both LED_SEL and FL_LVL inputs low-to-high. As
long as FL_LVL signal is held high, the flash LED remains
on unless it is on longer than the safety timer period. If
this occurs, the flash LED is turned off.
LDO Regulators
The AAT2860-x family include three LDO regulators. These
regulators are powered from the battery and produce a
fixed output voltage set through the I2C compatible serial
interface. The output voltage can be set to one of 16 out-
put voltages between 1.5V and 3.0V. The LDOs can also be
turned on/off through the I2C compatible serial interface.
The LDO regulators require only a small 2.2μF ceramic
output capacitor for stability. If improved load transient
response is required, larger-valued capacitors can be
used without stability degradation.
I2C Compatible Serial Interface
The AAT2860-x uses an I2C serial interface to set the LED
currents, the flash timer period, the LDO on/off and out-
put voltage, as well as other housekeeping functions. The
I2C interface takes input from a master device while the
AAT2860-x acts as a target to the master. The I2C protocol
uses two open-drain inputs; SDA (serial data line) and
SCL (serial clock line). Both inputs require an external pull
up resistor, typically to the input voltage. The I2C protocol
is bidirectional and allows target devices and masters to
both read and write to the bus. AAT2860 only supports
the write protocol and therefore the Read/Write bit must
always be set to “0”. The timing diagram in Figure 1 below
shows the typical transmission protocol.
I2C Compatible Serial Interface Protocol
The I2C compatible serial interface protocol is shown in
Figure 1. Devices on the bus can be either master or
target devices. Both master and target devices can both
send and receive data over the bus, with the difference
being that the master device controls all communication
on the bus. The AAT2860-x acts as a target device on the
bus and is only capable of receiving data and does not
transmit data over the bus.
The I2C communications begin with the master generat-
ing a START condition. Next, the master transmits the
7-bit device address and a read/write bit. Each target
device on the bus has a unique address. If the address
transmitted by the master matches the device address,
the target device transmits an acknowledge (ACK) signal
to indicate that it is ready to receive data. Since the
AAT2860-x only reads from the master, the read/write
bit must be set to “0”. Next, the master transmits an
8-bit register address, and the target device transmits
an ACK to indicate that it has received the register
address. Next, the master transmits an 8-bit data word,
and again the target device transmits an ACK indicating
that it has received the data. This process continues until
the master is finished writing to the target device at
which time the master generates a STOP condition.
START and STOP Conditions
START and STOP conditions are always generated by the
master. Prior to initiating a START, both the SDA and SCL
pin are active. As shown in Figure 2, a START condition is
when the master pulls the SDA line low and, after the
START condition hold time (tHD_STA), the master strobes the
SCL line low. A START condition acts as a signal to devices
on the bus that the device producing the START condition
is active and will be communicating on the bus.
SCL
SDA
Start
AAT 2860 Device
Address 0x60
W ACK Address = 02h ACK
Data = 40h
ACK Stop
Figure 1: Typical I2C Timing Diagram.
12
www.analogictech.com
2860.2008.05.1.0

12 Page





SeitenGesamt 23 Seiten
PDF Download[ AAT2860 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
AAT2860Backlight/Flash LED Driver and Multiple LDO Lighting Management UnitAdvanced Analogic Technologies
Advanced Analogic Technologies
AAT2862Backlight LED Driver And Multiple LDO Lighting Management UnitAnalogic Corporation
Analogic Corporation
AAT2868constant-frequency charge pump DC/DC converterAdvanced Analogic Technologies
Advanced Analogic Technologies
AAT2869constant-frequency charge pump DC/DC converterAdvanced Analogic Technologies
Advanced Analogic Technologies

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche