|
|
PDF AAT3104 Data sheet ( Hoja de datos )
| Número de pieza | AAT3104 | |
| Descripción | Low Cost 1x/2x 4 Channel Charge Pump WLED Driver | |
| Fabricantes | Advanced Analogic Technologies | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AAT3104 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
ChargePumpTM
PRODUCT DATASHEET
AAT3104178
Low Cost 1x/2x 4 Channel Charge Pump WLED Driver
General Description
The AAT3104 is a charge-pump based, current-source
white LED driver capable of driving one to four LEDs up
to 30mA, each. It automatically switches between 1x
mode and 2x mode to maintain the highest efficiency
and optimal LED current accuracy and matching.
The AAT3104 charge pump’s 1x mode (bypass mode)
has very low resistance allowing LED current regulation
to be maintained with input supply voltage approaching
www.DatatShheeeLt4EUD.cofmorward voltage.
LED brightness is controlled using AnalogicTech’s pat-
ented S2Cwire™ single wire interface. The AAT3104 is
available in a 2x2mm 10-lead SC70JW-10 package.
Features
• Drives up to 4 LEDs at up to 31mA each
• Automatic Switching Between 1x and 2x Modes
• 1MHz Switching Frequency
• Linear LED Output Current Control
• Single-wire, S2Cwire Interface
AAT3104-1: 16-step
AAT3104-2: 32-step
• ±10% LED Output Current Accuracy
• ±3% LED Output Current Matching
• Low-current Shutdown Mode
• Built-in Thermal Protection
• Automatic Soft-start
• Available in 2x2mm SC70JW-10 Package
Applications
• Cordless Phone Handsets
• Digital Cameras
• Mobile Phone Handsets
• MP3 and PMP Players
Typical Application
Input Voltage
2.7V to 5.5V
IN OUT
C+
CIN
1µF
CP
1µF
AAT3104
D1
C- D2
EN/SET
S2Cwire
Interface
EN/SET
GND
D3
D4
COUT
1µF
3104.2008.09.1.0
www.analogictech.com
1
1 page  
ChargePumpTM
PRODUCT DATASHEET
AAT3104178
Low Cost 1x/2x 4 Channel Charge Pump WLED Driver
Typical Characteristics
VIN = 3.6V, CIN = COUT = C1 = 1μF; TA = 25°C, unless otherwise noted.
1X Mode Turn-On Waveform
(VIN = 4.2V; Load = 120mA)
2X Mode Turn-On Waveform
(VIN = 3.6V; Load = 120mA)
VLED
(2V/div) 0
www.DataSheet4U.coIINm 0
(200mA/div)
VOUT
(2V/div) 0
EN
0
(1V/div)
Time (200µs/div)
VLED
(2V/div) 0
IIN 0
(250mA/div)
VOUT
(2V/div)
0
EN
(1V/div) 0
Time (200µs/div)
2X Mode Turn-Off Waveform
(VIN = 3.6V; Load = 120mA)
IIN
(250mA/div)
0
VLED
(2V/div)
0
EN
(1V/div) 0
Time (200µs/div)
VOUT
(AC Coupled) 0
(20mV/div)
2X Mode Output Ripple
(VIN = 3.6V; Load = 120mA)
VIN
(AC Coupled) 0
(5mV/div)
Time (0.4µs/div)
1mA to 30mA LED Current Step
(VIN = 4.2V)
VLED
2V/div
IIN 0
200mA/div 0
VOUT 0
2V/div
EN
1V/div
0
Time (80µs/div)
30mA to 1mA LED Current Step
(VIN = 4.2V)
VLED
(2V/div)
IIN
(200mA/div)
VOUT
(2V/div)
0
0
0
EN
(1V/div)
0
Time (80µs/div)
3104.2008.09.1.0
www.analogictech.com
5
5 Page 
ChargePumpTM
PRODUCT DATASHEET
AAT3104178
Low Cost 1x/2x 4 Channel Charge Pump WLED Driver
to outputs D1 through for a given constant current set-
ting. Depending on the combination of VIN and voltages
sensed at the current sources, the device will operate in
load switch mode. When any one of the voltages sensed
at the current sources nears dropout, the device will
operate in 2X charge pump mode.
Each of these modes will yield different efficiency values.
Refer to the following two sections for explanations for
each operational mode.
www.DataSheet4U.com
1X Mode Efficiency
The AAT3104 1X mode is operational at all times and
functions alone to enhance device power conversion effi-
ciency when VIN is higher than the voltage across the
load. When in 1X mode, voltage conversion efficiency is
defined as output power divided by input power.
An expression for the ideal efficiency (η) in 1X charge-
pump mode can be expressed as:
η
=
POUT
PIN
=
VF · ILED
VIN · IIN
=
VF
VIN
·
·
ILED
IOUT
≈
VF
VIN
-or-
η
(%)
=
VF
VIN
·
100
For a charge pump led driver with VF of 3.2V and 4.2V
input voltage, the theoretical efficiency is 76%. Due to
internal switching losses and IC quiescent current con-
sumption, the actual efficiency can be measured at 73%.
2X Charge Pump Mode Efficiency
The AAT3104 contains a charge pump which will boost
the input supply voltage in the event where VIN is less
than the voltage required to supply the output. The effi-
ciency (η) can be simply defined as a linear voltage
regulator with an effective output voltage that is equal to
one and two times the input voltage. Efficiency (η) for an
ideal 2X charge pump can typically be expressed as the
output power divided by the input power.
η=
PF
PIN
In addition, with an ideal 2X charge pump, the output
current may be expressed as 1/3 of the input current.
The expression to define the ideal efficiency (η) can be
rewritten as
η
=
POUT
PIN
=
VF · ILED
VIN · IIN
=
VF
VIN ·
· ILED
2 · IOUT
≈
2
VF
· VIN
-or-
η
(%)
=
2
VF
· VIN
·
100
For a charge pump current source driver with VF of 3.2V
and 2.7V input voltage, the theoretical efficiency is 59%.
Due to internal switching losses and IC quiescent current
consumption, the actual efficiency can be measured at
57%. Efficiency will decrease substantially as load cur-
rent drops below 1mA or when the voltage level at VIN
approaches the voltage level at VOUT.
Additional Applications
The current sources of the AAT3104 can be combined
freely to drive higher current levels through one LED. As
an example, a single LED can be driven at 120mA by
combining together D1 through D4 outputs.
For lower-cost applications, the flying capacitor can be
removed; C+ and C- should be floating. This will force
AAT3104 to operate in 1X mode. To maintain regulated
LED current, the input supply voltage has to be higher
than the charge-pump's dropout voltage in 1X mode plus
the forward voltage of the LED at the preset LED
current.
Capacitor Selection
Careful selection of the three external capacitors CIN, CP,
and COUT is important because they will affect turn-on
time, output ripple, and transient performance. Optimum
performance will be obtained when low equivalent series
resistance (ESR) ceramic capacitors are used, in general,
low ESR may be defined as less than 100mΩ. A value of
1μF for all four capacitors is a good starting point when
choosing capacitors. If the constant current sources are
only programmed for light current levels, then the
capacitor size may be decreased.
Capacitor Characteristics
Ceramic composition capacitors are highly recommended
over all other types of capacitors for use with the
AAT3104. Ceramic capacitors offer many advantages
over their tantalum and aluminum electrolytic counter-
parts. A ceramic capacitor typically has very low ESR, is
lowest cost, has a smaller PCB footprint, and is non-
polarized. Low ESR ceramic capacitors help maximizing
charge pump transient response. Since ceramic capaci-
tors are non-polarized, they are not prone to incorrect
connection damage.
3104.2008.09.1.0
www.analogictech.com
11
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet AAT3104.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AAT3103 | 3-Channel Charge-Pump LED Driver |  Advanced Analog Technology |
| AAT3104 | Low Cost 1x/2x 4 Channel Charge Pump WLED Driver | Advanced Analogic Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |