Datenblatt-pdf.com


GP1A05E2J00F Schematic ( PDF Datasheet ) - Sharp Electrionic

Teilenummer GP1A05E2J00F
Beschreibung OPIC Output Transmissive Photointerrupter
Hersteller Sharp Electrionic
Logo Sharp Electrionic Logo 




Gesamt 10 Seiten
GP1A05E2J00F Datasheet, Funktion
www.DataSheet4U.com
GP1A05EJ000F
Series
GP1A05EJ000F Series
Gap : 5mm, Slit : 0.5mm
*OPIC Output
Transmissive Photointerrupter
with Connector
Description
GP1A05EJ000F Series are standard, OPIC output,
transmissive photointerrupters with opposing emitter and
detector in a case, providing non-contact sensing. For
this family of devices, the emitter and detector are insert-
ed in a case, and a 3-pin connector is included to allow
remote-mount or off-board designs.
Features
1. Transmissive with OPIC output
2. Highlights :
• Includes additional screw xing holes
• Positioning Pin to prevent misalignment
3. Key Parameters :
• Gap Width : 5mm
• Slit Width (detector side) : 0.5mm
• Package : 34×18×11mm (without connector and
positloning pin)
• Connector : GP1A05EJ000F ; Tyco Electronics
AMP K.K. (PN : 171825-3)
GP1A05E2J00F ; J.S.T. Mfg Co., Ltd.
(PN : B3P-SHF-IAA (LF))
• Output Type : Low when the object is present.
4. Lead free and RoHS directive compliant
Agency approvals/Compliance
1. Compliant with RoHS directive
Applications
1. General purpose detection of object presence or mo-
tion.
2. Example: PPC, FAX, Printer
* "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signal-
processing
Notice The content of data sheet is subject to change without prior notice.
In the absence of conrmation by device specication sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specication sheets before using any SHARP device.
Sheet No.: D3-A06101EN
1 Date Oct. 3. 2005
© SHARP Corporation






GP1A05E2J00F Datasheet, Funktion
GP1A05EJ000F Series
Design Considerations
Design guide
1) Prevention of detection error
To prevent photointerrupter from faulty operation caused by external light, do not set the detecting face to
the external light.
2) In order to stabilize power supply line, connect a by-pass capacitor of more than 0.01μF between VCC and
GND near the device.
3) When the sensor is connected with long wire, noise might be on the signal from the sensor while it is
going through the wire. To avoid this problem, please evaluate the sensor under actual usage condition to
make sure that the system works ne.
4) Position of opaque board
Opaque board shall be installed at place 5mm or more from the top of elements.
(Example)
5mm or more
5) Screw tightening torque
The tightening torque for screwing should be 0.6Nm or less.
This product is not designed against irradiation and incorporates non-coherent IRED.
Parts
This product is assembled using the below parts.
• Photodetector (qty. : 1) [Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit]
Category
Maximum Sensitivity
wavelength (nm)
Sensitivity
wavelength (nm)
Response time (μs)
Photodiode
900
400 to 1 200
3
• Photo emitter (qty. : 1)
Category
Infrared emitting diode
(non-coherent)
Material
Gallium arsenide (GaAs)
Maximum light emitting
wavelength (nm)
950
I/O Frequency (MHz)
0.3
Sheet No.: D3-A06101EN
6

6 Page







SeitenGesamt 10 Seiten
PDF Download[ GP1A05E2J00F Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
GP1A05E2J00FOPIC Output Transmissive PhotointerrupterSharp Electrionic
Sharp Electrionic

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche