|
|
Número de pieza | DI-8B47 | |
Descripción | Linearized Thermocouple Input Modules | |
Fabricantes | ETC | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de DI-8B47 (archivo pdf) en la parte inferior de esta página. Total 2 Páginas | ||
No Preview Available ! DI-8B47 Linearized Thermocouple Input Modules
FEATURES
• Interfaces to Types J, K and T
• Linearizes Thermocouple Signal
• High Level Voltage Outputs
• 1500Vrms Transformer Isolation
• ANSI/IEEE C37.90.1
• Input Protected to 240VAC Continu-
ous
• 120dB CMR
• 70dB NMR at 60Hz
• Low Drift with Ambient Temperature
• Accurate CJC -40°C to +85°C
• CSA, FM, and CE Certifications
Pending
• Mix and Match Module Types
DESCRIPTION
DI-8B modules are an optimal solution
for monitoring real-world process signals
and providing high level signals to a data
acquisition system. Each DI-8B47 module
isolates, filters, amplifies, and linearizes a
single channel of temperature input from
www.DataSheet4aU.tchomermocouple and provides an analog
voltage output.
Linearization is accomplished using a four
breakpoint piecewise linear approximation.
The DI-8B47 can interface to industry
standard thermocouple type J, K, and T and
has an output signal of 0V to +5V. Each
module is cold-junction compensated to
correct for parasitic thermocouples formed
by the thermocouple wire and screw termi-
nals on the mounting backpanel. Upscale
open thermocouple detect is provided by
an internal pull-up resistor.
Signal filtering is accomplished with a
three-pole filter optimized for time and
frequency response which provides 70dB
of normal-mode-rejection at 60Hz. One
pole of this filter is on the field side of the
isolation barrier for anti-aliasing, and the
other two are on the system side.
A special input circuit on the DI-8B47
module provides protection against ac-
cidental connection of power-line voltages
up to 240VAC.
The modules are designed for installation
in Class I, Division 2 hazardous locations
and have a high level of immunity to envi-
ronmental noise.
SPECIFICATIONS
Typical at TA = +25ºC and +5V Power
DI-8B47
Input Range
-0.1V to +0.5V
Input Bias Current
-25nA
Input Resistance
Normal
Power Off
Overload
50MΩ
450kΩ
450kΩ
Input Protection
Continuous
Transient
240VAC
ANSI/IEEE C37.90.1
Sensor Excitation Current
0.25mA
Lead Resistance Effect
±0.02˚C/Ω¹
CMV, Input to Output
1500Vrms max
Transient, Input to Output
ANSI/IEEE C37.90.1
CMR (50Hz or 60Hz)
120dB
NMR
70dB at 60Hz
Accuracy
See Ordering Information on Page 2
Stability
Offset
Gain
±20ppm/ºC
±75ppm/ºC
Noise
Output, 100kHz
250µVrms
Bandwidth, -3dB
3Hz
Response Time, 90% Span
150ms
Output Range
0 to +5V
Output Protection
Transient
Continuous Short to Ground
ANSI/IEEE C37.90.1
Cold Junction Compensation
Accuracy, 25ºC
Accuracy, -40ºC to +85ºC
±0.5ºC
±1.5ºC
Power Supply Voltage
+5VDC ±5%
Power Supply Current
30mA
Power Supply Sensitivity
±25ppm/%
Mechanical Dimensions
1.11" × 1.65" × 0.40"
(28.1mm × 41.9mm × 10.2mm)
Environmental
Operating Temperature
Storage Temperature
Relative Humidity
-40ºC to +85ºC
-40ºC to +85ºC
0 to 95% Noncondensing
DATAQ Instruments, Inc. • 241 Springside Drive • Akron, Ohio 44333 • Tel: 330-668-1444 • Email: [email protected] • www.dataq.com
1 page |
Páginas | Total 2 Páginas | |
PDF Descargar | [ Datasheet DI-8B47.PDF ] |
Número de pieza | Descripción | Fabricantes |
DI-8B45 | Frequency Input Modules | ETC |
DI-8B47 | Linearized Thermocouple Input Modules | ETC |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |