DHR-C10 Datasheet PDF - LEM
| Part Number | DHR-C10 | |
| Description | AC/DC Current transducer | |
| Manufacturers | LEM | |
| Logo |  |
|
|
There is a preview and DHR-C10 download ( pdf file ) link at the bottom of this page. Total 3 Pages | ||
Preview 1 page No Preview Available !
AC/DC Current transducer DHR-C10
The transducer for the electronic measurement of DC & distorted AC
waveform currents, with galvanic isolation between the primary circuit
(power) and the secondary circuit (measurement). True RMS 0-10V
voltage output.
IPN = 100..1000 A
Electrical data
Primary Nominal
DC & AC Current
IPN (A.t.RMS)
100
200
300
400
500
600
1000
Primary AC Current
Max. Peak Value
IP (A) (*)
600
600
1000
1000
1800
1800
1800
Output voltage
(Analog)
VOUT (VDC)
0-10
0-10
0-10
0-10
0-10
0-10
0-10
R L Load resistance
VC Supply voltage
IC Current Consumption
VSL Output voltage limitation (0-10V)
ÎP Overload capability (Ampere Turns)
Performance data
X
εL
VOE
TCVOE
TCVOUT
tr
BW
Accuracy @ IPN, TA = 25°C (excluding offset)
Linearity error (1% of IPN .. ± IPN)
Electrical offset voltage, TA = 25°C
Temperature coefficient of VOE ( 0..+60 °C)
(-40..+70 °C)
Temperature coefficient of VOUT (% of reading)
Response time tp 90% of IPN step
Frequency bandwidth (±1dB)
General data
TA
TS
m
IPxx
Ambient operating temperature
Ambient storage temperature
Mass
Protection degree
Type
DHR 100 C10
DHR 200 C10
DHR 300 C10
DHR 400 C10
DHR 500 C10
DHR 600 C10
DHR 1000 C10
≥ 10
kΩ
+ 20 .. 50 V DC
30 mA
< 14
V
30000
A.t
< ± 1 % of IPN
< ± 1.0 % of IPN
< ± 1.0 % of IPN
± 2.0 mV/K
± 4.0 mV/K
± 0.1
%/K
< 150
ms
DC 20..6000Hz
- 40 .. + 70
- 40 .. + 85
260
IP20
°C
°C
g
Note :
(*) The Max. Peak AC Current is the highest peak level of the primary signal that is
taken into account for accurate True RMS calculation. Yet the device is designed for
maximum continuous True RMS value equal to IPN, whereas the output is limited by
the above specified output limitation.
Features
• VFD and SCR waveforms current
measurement
• True RMS output
• Panel mounting
• Eliminates insertion loss
• Insulated plastic case recognized
according to UL94-V0
Advantages
• Large aperture for cable up to
Ø32mm
• High isolation between primary and
secondary circuits
• Easy installation
Applications
• VFD Controlled Loads
VFD output indicates how the motor
and attached load are operating.
• SCR Controlled Loads
Acurate measurement of phase
angle fired or burst fired (time
proportioned) SCRs. Current
measurement gives faster
response than temperature
measurement.
• Switching Power Supplies and
Electronic Ballasts
True RMS sensing is the most
accurate way to measure power
supply or ballast input power.
Application domain
• Energy and Automation
061128/14
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
Page 1/3
www.lem.com
|
| |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DHR-C10 electronic component. |
| Information | Total 3 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ DHR-C10.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| DHR-C10 | The function is AC/DC Current transducer. LEM | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
DHR-
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||