|
|
PDF PE4232 Data sheet ( Hoja de datos )
| Número de pieza | PE4232 | |
| Descripción | SPST CATV UltraCMOS Switch | |
| Fabricantes | Peregrine Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PE4232 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Product Description
The PE4232 is a is a high-isolation Switch designed for CATV
applications, covering a broad frequency range from near DC
up to 1300 MHz. This single-supply SPST switch offers a
single-pin CMOS control interface with industry leading CTB
performance. It also provides low insertion loss, high isolation
and extremely low bias requirements while operating on a
single 3-volt supply. In a typical CATV application, the PE4232
provides for a cost effective and manufacturable solution vs.
mechanical relays.
The PE4232 is manufactured on Peregrine’s UltraCMOS™
process, a patented variation of silicon-on-insulator (SOI)
technology on a sapphire substrate, offering the performance
of GaAs with the economy and integration of conventional
CMOS.
Figure 1. Functional Diagram
RF1 RF2
Product Specification
PE4232
SPST CATV UltraCMOS™ Switch
Features
• Non-reflective 75 Ω switch
• Integrated 0.25 watt terminations
• CTB performance of 100 dBc
• High isolation: 90 dB at 5 MHz,
53 dB at 1000 MHz
• Low insertion loss: 0.5 dB at 5 MHz,
0.75 dB at 1000 MHz
• High input IP2: 80 dBm
• CMOS/TTL single-pin control
• Single +3-volt supply operation
• Extremely low bias: 33 µA @ 3 V
Figure 2. Package Type
6-lead DFN
75
CMOS
75
Control
Driver
CTRL
Table 1. Electrical Specifications @ +25 °C (ZS = ZL = 75 Ω)
Parameter
Operating Frequency1
Condition
Minimum
DC
Operating Power
Insertion Loss
Isolation
Return Loss
Input 1 dB Compression2,4
CTB / CSO
Input IP22
Input IP32
Video Feedthrough3
On / Off
DC – 50 MHz
1000 MHz
DC – 50 MHz
1000 MHz
5 - 1000 MHz
1000 MHz
77 & 110 channels;
PO = 44 dBmV
1000 MHz
1000 MHz
75
50
14
30
80
50
Switching Time
Notes: 1. Device linearity will begin to degrade below 1 MHz.
2. Measured in a 50 Ω system.
3. Measured with a 1 ns risetime, 0/3 V pulse and 500 MHz bandwidth.
4. Note Absolute Maximum ratings in Table 3.
Document No. 70-0054-03 │ www.psemi.com
Typical
0.5
0.75
90
53
20
33
-100
2
Maximum
1300
30/24
0.65
1.0
15
Units
MHz
dBm
dB
dB
dB
dBm
dBc
dBm
dBm
mVpp
µs
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 1 of 8
1 page  
PE4232
Product Specification
Evaluation Kit
The SPST Switch Evaluation Kit board was
designed to ease customer evaluation of the
PE4232 SPST switch. The RF1 port is connected
through a 75 Ω transmission line to the top left
BNC connector, J1. The RF2 port is connected
through a 75 Ω transmission line to the BNC
connector on the top right side of the board, J2. A
through transmission line connects BNC
connectors J3 and J4. This transmission line can
be used to estimate the loss of the PCB over the
environmental conditions being evaluated.
The board is constructed of a two metal layer FR4
material with a total thickness of 0.031”. The
bottom layer provides ground for the RF
transmission lines. The transmission lines were
designed using a coplanar waveguide model with
trace width of 0.021”, trace gaps of 0.030”,
dielectric thickness of 0.028”, metal thickness of
0.0021” and εR of 4.3. Note that the predominate
mode for these transmission lines is coplanar
waveguide with a ground plane.
J5 provides a means for controlling DC and digital
inputs to the device. Starting from the lower left
pin, the second pin to the right (J5-3) is connected
to the device VDD input. The fourth pin to the right
(J5-7) is connected to the device CTRL input. It is
the responsibility of the customer to determine
proper supply decoupling for their design
application. Removing these components from
the evaluation board has not been shown to
degrade RF performance.
Figure 11. Evaluation Board Layouts
Peregrine Specification 101/0079
Figure 12. Evaluation Board Schematic
Peregrine Specification 102/0081
Document No. 70-0054-03 │ www.psemi.com
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 5 of 8
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet PE4232.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PE4230 | SPDT High Power UltraCMOS RF Switch | Peregrine Semiconductor |
| PE4231 | SPDT High Power UltraCMOS | Peregrine Semiconductor |
| PE4232 | SPST CATV UltraCMOS Switch | Peregrine Semiconductor |
| PE423422 | SPDT RF Switch | Peregrine Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |