|
|
PDF ECP100D Data sheet ( Hoja de datos )
| Número de pieza | ECP100D | |
| Descripción | High Linearity InGaP HBT Amplifier | |
| Fabricantes | WJ Communication | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ECP100D (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
ECP100D
1 Watt, High Linearity InGaP HBT Amplifier
The Communications Edge TM
Product Information
Product Features
Product Description
x 400 – 2300 MHz
x +31.5 dBm P1dB
x +46 dBm Output IP3
x 18 dB Gain @ 900 MHz
x 12 dB Gain @ 1960 MHz
x Single Positive Supply (+5V)
x Lead-free/Green/RoHS-compliant
16pin 4mm QFN package
Applications
x Final stage amplifiers for
Repeaters
x Mobile Infrastructure
x Defense / Homeland Security
The ECP100D is a high dynamic range driver amplifier
in a low-cost surface mount package. The InGaP/GaAs
HBT is able to achieve superior performance for various
narrowband-tuned application circuits with up to +46
dBm OIP3 and +31.5 dBm of compressed 1-dB power.
It is housed in an industry standard Lead-
free/Green/RoHS-compliant 16-pin 4x4mm QFN SMT
package. All devices are 100% RF and DC tested.
The product is targeted for use as driver amplifier for
various current and next generation wireless
technologies such as GPRS, GSM, CDMA, W-CDMA,
and UMTS, where high linearity and high power is
required. The internal active bias allows the ECP100D
to maintain high linearity over temperature and operate
directly off a +5 V supply.
Functional Diagram
Vref 1
N/C 2
RF IN 3
N/C 4
16 15 14
567
13
12 N/C
11 RF OUT
10 RF OUT
9 N/C
8
Function
Vref
RF Input
RF Output
Vbias
GND
N/C or GND
Pin No.
1
3
10, 11
16
Backside Paddle
2, 4-9, 12-15
Specifications (1)
Parameter
Operational Bandwidth
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Output IP3 (2)
IS-95 Channel Power
@ -45 dBc ACPR, 1960MHz
W-CDMA Channel Power
@ -45 dBc ACPR, 2140 MHz
Noise Figure
Operating Current Range , Icc (3)
Device Voltage, Vcc
Units
MHz
MHz
dB
dB
dB
dBm
dBm
dBm
dBm
dB
mA
V
Min
400
10
+29
+43.8
400
Typ
2140
11
18
8
+31.5
+45
+25.5
+23
6.3
450
5
Max
2300
500
1. Test conditions unless otherwise noted: T = 25 ºC, Vsupply = +5 V in a tuned application circuit.
2. 3OIP measured with two tones at an output power of +15 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
3. This corresponds to the quiescent current or operating current under small-signal conditions into
pins 10, 11 and 16. It is expected that the current can increase by an additional 90 mA at P1dB.
Pin 1 is used as a reference voltage for the internal biasing circuitry. It is expected that Pin 1 will
pull 10.8 mA of current when used with a series bias resistor of R1=51 ¡ . (ie. total device current
typically will be 461 mA.)
Typical Performance (4)
Parameter
Frequency
S21 – Gain
S11
S22
Output P1dB
Output IP3
IS-95A Channel Power
@ -45 dBc ACPR
W-CDMA Channel Power
@ -45 dBc ACPR
Noise Figure
Supply Bias (3)
Units
MHz
dB
dB
dB
dBm
dBm
dBm
dBm
dB
Typical
900 1960 2140
18 12
11
-13 -11
-18
-7 -10
-8
+31 +32 +31.5
+46 +46
+45
+25.
5
+25.5
+23
7.0 5.5
6.2
+5 V @ 450 mA
4. Typical parameters reflect performance in a tuned application circuit at +25 C.
¢
Absolute Maximum Rating
Parameter
Operating Case Temperature
Storage Temperature
RF Input Power (continuous)
Device Voltage
Device Current
Device Power
Junction Temperature
Rating
-40 to +85 qC
-65 to +125 qC
+26 dBm
+8 V
900 mA
5W
+250 qC
Operation of this device above any of these parameters may cause permanent damage.
Ordering Information
Part No.
ECP100D-G
ECP100D-PCB900
ECP100D-PCB1960
ECP100D-PCB2140
Description
1 Watt InGaP HBT Amplifier
(Lead-free/Green/RoHS-compliant 16-pin 4x4mm Pkg.)
900 MHz Evaluation Board
1960 MHz Evaluation Board
2140 MHz Evaluation Board
Specifications and information are subject to change without notice
WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com
Page 1 of 7 April 2006
1 page  
ECP100D
1 Watt, High Linearity InGaP HBT Amplifier
The Communications Edge TM
Product Information
2140 MHz Application Circuit (ECP100D-PCB2140)
Typical RF Performance at 25 qC
Frequency
2140 MHz
S21 – Gain
11 dB
S11 – Input Return Loss
-18 dB
S22 – Output Return Loss
-8.0 dB
Output P1dB
+31.5 dBm
Output IP3
(+15 dBm / tone, 1 MHz spacing)
+45 dBm
Channel Power
(@-45 dBc ACPR, IS-95 9 channels fwd)
+23 dBm
Noise Figure
6.2 dB
Device / Supply Voltage
+5 V
Quiescent Current (1)
450 mA
1. This corresponds to the quiescent current or operating current under
small-signal conditions into pins 6, 7, and 8.
P ORT
P =1
Z=50 Ohm
CAP
ID=C1
C=56 pF
RES
ID=R3
R=51 Ohm
CA P
I D=C2
C=56 pF
·The transmission line length are from the
edge of the ECP100D pins to the cent er of t he component.
All passive components are of size 0603 unless otherwise noted.
CA P
ID=C5
C=1000 pF
RES
ID=R1
R=51 Ohm
RE S
ID=R2
R=22 Ohm
TL INP
1136 1145 1154 1163
ID=FR1
Z0=50 Ohm
L=375 mil
112
112
E ef f=3. 16
Loss =0
F0=0 MHz
121
130
SUBCKT
ID=E CP1 00 D
NE T="Q FN"
121
103
CAP
I D=C8
C=1.0 pF
49 94
58 76 76 85
This component should be plac ed at silk s creen mark er
"G" on the WJ evaluation board as shown.
+5 V
+5.6 V zener
IND
ID=L1
L=18 nH
size 1008
CAP
ID=C4
C=10000000 pF
CAP
ID=C7
C=1000 pF
CA P
ID=C6
C=10 pF
CA P
I D=C3
C=56 pF
PORT
P=2
Z=50 Ohm
TLINP
ID=FR4
Z0=50 Ohm
L=175 mil
E ef f=3. 16
Loss=0
F0=0 MHz
CAP
ID=C9
C=2.4 pF
This component should be placed
at silk screen marker "3" on the
WJ evaluation board as shown.
S21 vs. Frequency
15
12
9
6 +25°C
3
+85°C
-40°C
0
2110 2120 2130 2140 2150 2160 2170
Frequency (MHz)
S22 vs. Frequency
0
-5
-10
+25°C
-15 +85°C
-40°C
-20
2110 2120 2130 2140 2150 2160 2170
Frequency (MHz)
P1 dB vs. Frequency
34
32
30
28
+25°C
+85°C
26 -40°C
24
2110 2120 2130 2140 2150 2160 2170
Frequency (MHz)
S11 vs. Frequency
-10
-14
-18
-22 +25°C
-26
+85°C
-40°C
-30
2110 2120 2130 2140 2150 2160 2170
Frequency (MHz)
Noise Figure vs. Frequency
9
8
7
6
5
4
3
2
+25°C
+85°C
1 -40°C
0
2110 2120 2130 2140 2150 2160 2170
Frequency (MHz)
ACPR vs. Channel Power
3GPP W-CDMA, Test Model 1+64 DPCH, ±5MHz offset, 2140 MHz
-40
-45
-50
-55
+25°C
+85°C
-60 -40°C
-65
19
20Output C2h1annel Po2w2er (dBm2)3
24
OIP3 vs. Temperature
freq. = 2140, 2141 MHz, +15 dBm / tone
50
47
44
41
38
35
-40
-15 10 35 60
Temperature (°C )
OIP3 vs. Frequency
+25°C, +15 dBm / tone
50
85
47
44
41
38
35
2110 2120 2130 2140 2150 2160 2170
Frequency (MHz)
OIP3 vs. Output Power
freq. = 2140, 2141 MHz, 25°C
50
47
44
41
38
35
10 12 14 16 18 20 22
Output Power (dBm)
Specifications and information are subject to change without notice
WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com
§
§§
§
Page 5 of 7 April 2006
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet ECP100D.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ECP100D | High Linearity InGaP HBT Amplifier | WJ Communication |
| ECP100G | High Gain HBT Amplifier | WJ Communication |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |