Datenblatt-pdf.com


DEH-11 Schematic ( PDF Datasheet ) - Pioneer

Teilenummer DEH-11
Beschreibung (DEH-xxxx) Manual
Hersteller Pioneer
Logo Pioneer Logo 




Gesamt 6 Seiten
DEH-11 Datasheet, Funktion
www.DataSheet4U.com
DEH-2100
DEH-1100
DEH-21
DEH-11
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit
est conforme à CEMA.
Los colores de los cables este producto se conforman
con el código de colores CEMA.
www.DataSheet4U.com
Printed in U.S.A.
Imprimé aux Etats-Unis
<HRD0147-A> UC
<99K00T0T01>
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
• To avoid shorts in the electrical system, be sure
to disconnect the battery cable before begin-
ning installation.
• Refer to the owner’s manual for details on con-
necting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
• Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
or the left and right speaker leads are com-
mon.
• Speakers connected to this unit must be high-
power types with minimum rating of 40 W
(45 W)* and impedance of 4 to 8 ohms.
Connecting speakers with output and/or imped-
ance values other than those noted here may
result in the speakers catching fire, emitting
smoke, or becoming damaged.
* DEH-2100 and DEH-21
• When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal. (Max. 300 mA 12 V DC.) If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
• To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a pos-
sibility of short-circuiting if the leads are not
insulated.
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.
F ACC O
FO
ACC position
No ACC position
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
• Cords for this product and those for other prod-
ucts may be different colors even if they have the
same function. When connecting this product to
another product, refer to the supplied Installation
manuals of both products and connect cords that
have the same function.
Connection Diagram
<ENGLISH>
Perform these connections when using a different amp (sold separately).
Rear output
This Product
Antenna jack
Connecting cords with RCA
pin plugs (sold separately)
To system control terminal of
Fuse the power amp or Auto-antenna
relay control terminal.
(Max. 300 mA 12 V DC.)
Blue/white
Fuse holder
System remote control
Power amp
(sold separately)
To vehicle (metal) body.
Black (ground)
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
To terminal always supplied with power
regardless of ignition switch position.
Red
Yellow
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Front
speaker
Left
Rear
speaker
+
+
Rear
speaker
+
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
+
Front
speaker
Right
+
Rear
speaker
+ Rear
speaker






DEH-11 Datasheet, Funktion
www.DataSheet4U.com
Instalación
Nota:
• Antes de finalmente instalar la unidad, conecte el
cableado temporalmente y asegúrese de que todo
esté conectado correctamente y que la unidad y el
sistema funcionan debidamente.
• Utilice sólo las piezas que se incluyen con esta
unidad para asegurar la instalación adecuada. El
uso de piezas no autorizadas podría causar fallos
de funcionamiento.
• Consulte con su distribuidor si la instalación
requiere del taladro de orificios u otras modifica-
ciones del vehículo.
• Instale la unidad donde no alcance el espacio del
conductor, y donde no pueda dañar a los
pasajeros si sucediera un paro repentino, como
una detención de emergencia.
• El semiconductor láser se dañará si se sobre-
calienta, por eso no instale la unidad en un lugar
caliente – por ejemplo, cerca de la salida de un
calefactor.
• Si el ángulo de la instalación excede los 60° del
lado horizontal, la unidad podría no brindar su
óptimo funcionamiento.
60°
Montaje delantero/trasero DIN
Esta unidad quede instalarse correstamente de la “Delantera” (montaje delantero DIN convenciona) o
“Trasera” (montaje trasero DIN, utilizando los tornillos roscados en los constados del chasis de la unidad).
Para detalles, refiérase a los métodos de instalación ilustrados abajo.
Montaje delantero DIN
Instalación con tope de goma
Tablero de instrumentos
182
53
Soporte
Después de insertar el soporte en la tabla
de mandos, luego seleccione las orejetas
apropiadas según el grosor del material
de la tabla de mandos y dóblelos.
(Instale lo más firme posible usando las
lengüetas superior e inferior. Para fijar,
doble las lengüetas 90 grados.)
Tope de goma
Tornillo
www.DataSheet4U.com
Quitado de la unidad
Marco
Inserte el pasador de liberan-
ción en el orificio de la parte
inferior del marco, y tire hacia
afuera para extraer el marco.
(Para la fijación del marco,
apunte el lado con ranura hacia
abajo.)
Montaje trasero DIN
Instalación usando los agujeros para tornillos ubicados en ambos costados de la unidad
1. Quite el marco.
Marco
Inserte el pasador de liberanción
en el orificio de la parte inferior
del marco, y tire hacia afuera
para extaer el marco.
(Para la fijación del marco,
apunte el lado con ranura hacia
abajo.)
<ESPAÑOL>
2. Fijación de la unidad a la ménsula de montaje existente.
Seleccione una posición en la que los orificios para los tornil-
los del soporte y del de la unidad principal queden alineados,
y apriete los tornillos en 2 lugares de un lado. Utilice ya sea
los tornillos de fijación (5 × 8 mm) o los tornillos a paño (5 ×
9 mm), dependiendo de la forma de los orificios de tornillo en
la ménsula.
Inserte las herramientas de extracción
suministradas en la unidad, como se
indica en la figura, hasta que se
enganchen en su positión.
Tire de la unidad mientras mantiene
las herramientas presionadas contra
los lados de la unidad.
Ménsula de montaje de
radio existente
Tornillo
Tablero de instrumentos
o consola

6 Page







SeitenGesamt 6 Seiten
PDF Download[ DEH-11 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
DEH-11(DEH-xxxx) ManualPioneer
Pioneer
DEH-1100(DEH-xxxx) ManualPioneer
Pioneer
DEH-1100HIGH POWER CD PLAYERPioneer
Pioneer
DEH-1700Service ManualPioneer
Pioneer
DEH-1700Operation ManualPioneer
Pioneer

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche