|
|
Número de pieza | UB084S01 | |
Descripción | LCD_Module | |
Fabricantes | DATAMODUL | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de UB084S01 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
No Preview Available ! et4U.comU N I PA C O P T O E L E C T R O N I C S C O R P O R AT I O N
he Spec. No. 413-212-061
taS Version :
B
a Total pages : 13
www.D Date : 2000.03.30
omUB084S01 COLOR TFT-LCD
.cMODULE SPECIFICATION
t4UMODEL NAME: UB084S01
heeThe content of this technical information
Sis subject to change without notice.
taPlease contact Unipac or its agent for
further information.
www.DaApproved by Checked by Prepared by
.DataSheet4U.comUnipac copyright 2000
All rights reserved,
www Copying forbidden.
1 page SPEC NO. : 413-212-061
PAGE
: 3/13
B. Electrical specifications
1.Pin assignment
(1).Input signal interface
Pin no
Symbol
Function
1 VCC +3.3 V power supply
2 VCC +3.3 V power supply
3
GND
Ground
4
GND
Ground
5
RxIN0-
LVDS receiver signal channel 0
6 RxIN0+
7
GND
Ground
8
RxIN1-
LVDS receiver signal channel 1
9 RxIN1+
10
GND
Ground
11
RxIN2-
LVDS receiver signal channel 2
12 RxIN2+
13
GND
Ground
14
CKIN-
LVDS receiver signal clock
15 CKIN+
16
GND
Ground
17 NC No Connection
18 NC No Connection
19
GND
Ground
20
GND
Ground
Etc.
5 Page SPEC NO. : 413-212-061
PAGE
: 9/13
e.Backlight driving conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
Remark
Lamp voltage
Lamp current
Power consumption
Lamp starting voltage
VL
IL
PL
VS
-
426
-
Vrms
Note 1
-
4.6
-
mArms
Note 1
- 1.9 -
W Note 2
TBD
TBD
Vrms
T=0
T=25
Frequency
FL - 60 - KHZ Note 3
Lamp life time
LL 10000
-
- Hr Note 1, 4
Note 1: T= 25, IL = 4.6mA.
Note 2: Inverter should be designed with the characteristic of lamp. When you are designing
the inverter, the output voltage of the inverter should comply with the following
conditions.
(1).The area under the positive and negative cycles of the waveform of the lamp
current and lamp voltage should be area symmetric(the symmetric ratio should be
larger than 90%).
(2).There should not be any spikes in the waveform.
(3).The waveform should be sine wave as possible.
(4).Lamp current should not exceed the maximum value within the operating
temperature (It is prohibited to over the maximum lamp current even if operated in
the non-guaranteed temperature). When lamp current over the maximum value for
a long time, it may cause fire. Therefore, it is recommend that the inverter should
have the current limiter circuit.
Note 3: Lamp frequency may produce interference with horizontal synchronous frequency and
this may cause line flow on the display. Therefore lamp frequency shall be detached
from the horizontal synchronous frequency and its harmonics as far as possible in
order to avoid interference. In case using the inverter by PWM control, PWM
frequency may interference with frame frequency. We suggest that PWM frequency
is same as frame frequency.
Note 4: Brightness to be decrease to the 50% of the initial value.
Note 5: CN2 connector(backlight): TBD
Mating connector: TBD
Pin no.
1
2
Symbol
H
L
Function
CCFL power supply(H.V.)
CCFL power supply(GND)
Remark
Cable color: Pink
Cable color: White
11 Page |
Páginas | Total 15 Páginas | |
PDF Descargar | [ Datasheet UB084S01.PDF ] |
Número de pieza | Descripción | Fabricantes |
UB084S01 | LCD_Module | DATAMODUL |
UB084S01-1 | TFT LCD TOUCH PANEL | DATAMODUL |
UB084S01-2 | TFT LCD TOUCH PANEL | DATAMODUL |
ub084s011 | LCD_Module | DATAMODUL |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |