|
|
PDF EP82562GT Data sheet ( Hoja de datos )
| Número de pieza | EP82562GT | |
| Descripción | 10/100 Mbps Platform LAN Connect | |
| Fabricantes | Intel | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de EP82562GT (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
h8Ce2eo5tn46nU2e.GccoTtm(1P0L/1C0)0 Mbps Platform LANNetworking Silicon
.DataS Product Features
Datasheet
ww ■ IEEE 802.3 10BASE-T/100BASE-TX
w compliant physical layer interface
m■ IEEE 802.3u Auto-Negotiation support
■ Digital Adaptive Equalization control
o■ Link status interrupt capability
.c■ XOR tree mode support
■ 3-port LED support (speed, link and
activity)
U■ 10BASE-T auto-polarity correction
t4■ LAN Connect Interface
■ PHY detects polarity, MDI-X, and cable
lengths. Auto MDI, MDIX crossover at all
espeeds
■ Diagnostic loopback mode
■ 1:1 transmit transformer ratio support
■ Low power (less than 300 mW in active
transmit mode)
■ Reduced power in “unplugged mode” (less
than 50 mW)
■ Automatic detection of “unplugged mode”
■ 3.3 V device
■ Lead-free1 48-pin Shrink Small Outline
Package for both leaded and lead-free
designs. (Devices that are lead-free are
marked with a circled “e3” and have the
product code prefix: LUxxxxxx).
e1 This device is lead-free. That is, lead has not been intentionally added, but lead may still exist
as an impurity at <1000 ppm. The Material Declaration Data Sheet, which includes lead
himpurity levels and the concentration of other Restriction on Hazardous Substances (RoHS)-
banned materials, is available at:
Sftp://download.intel.com/design/packtech/material_content_IC_Package.pdf#pagemode=bookmarks
In addition, this device has been tested and conforms to the same parametric specifications as
taprevious versions of the device.
For more information regarding lead-free products from Intel Corporation, contact your Intel
aField Sales representative.
.DAdditional Features
■ The 82562GT PLC supports drop-in replacement with the 82562ET. If it is not used as a drop-
in replacement, strapping options enable new operating modes:
w—LED support for three logic configurations.
— LAN disable function using one pin.
w—Increased transmit strength.
m■ The receive BER performance increases the margin for cable length.
w o■ Return Loss performance is improved.
.DataSheet4U.cRevision 1.4
www April 2005
1 page  
Networking Silicon — 82562GT
8.2.5 100BASE-TX Voltage and Current DC Specifications ..........................33
8.3 AC Characteristics...............................................................................................34
8.3.1 10BASE-T Normal Link Pulse (NLP) Timing Parameters .....................34
8.3.2 Auto-Negotiation Fast Link Pulse (FLP) Timing Parameters .................35
8.3.3 100BASE-TX Transmitter AC Specifications .........................................36
8.3.4 Reset (JRSTSYNC) AC Specifications .................................................36
9.0 Package and Pinout Information ..................................................................................37
9.1 Package Information ...........................................................................................37
9.2 Pinout Information ...............................................................................................38
9.2.1 82562GT Pin Assignments ....................................................................38
9.2.2 82562GT Shrink Small Outline Package Diagram ................................39
Datasheet
v
5 Page 
Networking Silicon — 82562GT
Table 1. 82562GT Hardware Configuration
TESTEN
ISOL
_TCK
ISOL
_TI
ISOL_
EXEC
Mode
1 1 0 1 Reserved
1 1 1 0 Reserved Testing
1 1 1 1 Power-down Mode
Comments
The ISOL_TI pin has an internal
10 K Ω pull-down resistor and
should not be connected.
The ISOL_EXEC pin has an
internal 10 K Ω pull-down resistor
and should not be connected.
Tri-state and power down.
NOTE: Combinations not shown in Table 1 are reserved and should not be used.
Table 2. LED Logic Functionality
Mode/Configuration
Configuration A:
82562ET-compatible
Configuration B: Intel
GbE mode
Configuration C:
Alternative mode
ACTLED#
SPDLED#
Activity Speed 100 Mb
Activity Link and Speed 100 Mb
Activity Link and Speed 100 Mb
LILED#
Asserted if valid link is present at
10 Mb or 100 Mb
Asserted if valid link is present at
10 Mb or 100 Mb
Link and Speed 10 Mb
Datasheet
5
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet EP82562GT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| EP82562G | 10/100 Mbps Platform LAN Connect | Intel |
| EP82562GT | 10/100 Mbps Platform LAN Connect | Intel |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |