Datenblatt-pdf.com


D116EI Schematic ( PDF Datasheet ) - MicroPower Direct

Teilenummer D116EI
Beschreibung (D111EI Series) High Isolation SIP DC/DC Converters
Hersteller MicroPower Direct
Logo MicroPower Direct Logo 




Gesamt 2 Seiten
D116EI Datasheet, Funktion
D100EI Series
Low Cost, 1W
High Isolation SIP
DC/DC Converters
New Budget Saver!!
Electrical Specications
Specications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specications subject to change without notice.
Key Features:
Input
Parameter
Conditions
Min. Typ. Max. Units
1W Output Power
5 VDC Input 4.5 5.0 5.5
3,000 VDC Isolation
Miniature SIP Case
Single & Dual Outputs
>1 MHour MTBF
24 Standard Models
LOWEST COST!!
Input Voltage Range
Input Filter
Reverse Polarity Input Current
Output
Parameter
Output Voltage Accuracy
12 VDC Input 10.8 12.0
24 VDC Input 21.6 24.0
Internal Capacitor
13.2
26.4
0.3
VDC
A
Conditions
Min. Typ. Max.
±1.0 ±3.0
Units
%
Output Voltage Balance
Dual Output , Balanced Loads
±0.1 ±1.0
%
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation (Note 1)
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
50 75 mV P - P
Output Power Protection
120 %
Temperature Coefcient
±0.02 ±0.03 %/ºC
Output Short Circuit
Momentary (1.0 Sec.)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 3,000
VDC
Isolation Resistance
500 VDC 1,000
MΩ
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
100 150 200
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Operating Temperature Range
Case -40
+90 ºC
Storage Temperature Range
-55
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95 %
MicroPower Direct Physical
232 Tosca Drive
Case Size
0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm)
Stoughton, MA 02072
USA
omT: (781) 344-8226
.cF: (781) 344-8481
www.datasheet4uW: www.micropowerdirect.com
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.07 Oz (2.1g)
Reliability Specications
Parameter
Conditions
Min. Typ. Max. Units
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign 1.0
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input -0.7
9.0
Input Voltage Surge (1 Sec)
12 VDC Input -0.7
18.0 VDC
24 VDC Input -0.7
30.0
Lead Temperature
1.5 mm From Case For 10 Sec
300 ºC
Internal Power Dissipation
All Models
450 mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.





SeitenGesamt 2 Seiten
PDF Download[ D116EI Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
D116EI(D111EI Series) High Isolation SIP DC/DC ConvertersMicroPower Direct
MicroPower Direct

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche