DS1603 Datasheet PDF - Dallas
| Part Number | DS1603 | |
| Description | Elapsed Time Counter Module | |
| Manufacturers | Dallas | |
| Logo |  |
|
|
There is a preview and DS1603 download ( pdf file ) link at the bottom of this page. Total 8 Pages | ||
Preview 1 page No Preview Available !
www.dalsemi.com
DS1603
Elapsed Time Counter Module
FEATURES
§ Two 32–bit counters keep track of real time
and elapsed time
§ Counters keep track of seconds for over 125
years
§ Battery powered counter counts seconds from
the time battery is attached until VBAT is less
than 2.5 volts
§ VCC powered counter counts seconds while
VCC is above 4.25 volts and retains the count
in the absence of VCC under battery backup
power
§ Clear function resets selected counter to 0
§ Read/Write serial port affords low pin count
§ Powered internally by a lithium energy cell
that provides over 10 years of operation
§ 1-byte protocol defines read/write, counter
address and software clear function
§ Self-contained crystal provides an accuracy of
±2 min per month
§ Operating temperature range of 0°C to 70°C
§ Low profile SIP module
PIN ASSIGNMENT
VCC
RST
DQ
NC
CLK
OSC
GND
1
2
3
4
5
6
7
PIN DESCRIPTION
RST
CLK
DQ
GND
VCC
OSC
NC
- Reset
- Clock
- Data Input/Output
- Ground
- +5 Volts
- 1 Hz Oscillator Output
- No Connect
DESCRIPTION
The DS1603 is a real time clock/elapsed time counter designed to count seconds when VCC power is
applied and continually count seconds under battery backup power with an additional counter regardless
of the condition of VCC. The continuous counter can be used to derive time of day, week, month, and year
by using a software algorithm. The VCC powered counter will automatically record the amount of time
that VCC power is applied. This function is particularly useful in determining the operational time of
equipment in which the DS1603 is used. Alternatively, this counter can also be used under software
control to record real time events. Communication to and from the DS1603 takes place via a 3–wire
serial port. A 1-byte protocol selects read/ write functions, counter clear functions and oscillator trim. The
device contains a 32.768 kHz crystal which will keep track of time to within ±2 min/mo. An internal
lithium energy source contains enough energy to power the continuous seconds counter for over 10 years.
OPERATION
The main elements of the DS1603 are shown in Figure 1. As shown, communications to and from the
elapsed time counter occur over a 3–wire serial port. The port is activated by driving RST to a high state.
With RST at high level 8 bits are loaded into the protocol shift register providing read/write, register
select, register clear, and oscillator trim information. Each bit is serially input on the rising edge of the
1 of 8
080299
|
| |
 
DATA TRANSFER Figure 3
DS1603
TIMING DIAGRAM: READ/WRITE DATA TRANSFER
NOTE: tCL, tCH, tR, and tF apply to both read and write data transfer.
5 of 8
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DS1603 electronic component. |
| Information | Total 8 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ DS1603.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| DS160-40THD02 | The function is SCHOTTKY BARRIER DIODE. JCET |  |
| DS1602 | The function is Elapsed Time Counter. Dallas | |
| DS1603 | The function is Elapsed Time Counter Module. Dallas | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
DS16
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||