Datenblatt-pdf.com


PCF1252-1 Schematic ( PDF Datasheet ) - NXP Semiconductors

Teilenummer PCF1252-1
Beschreibung Threshold detector and reset generator
Hersteller NXP Semiconductors
Logo NXP Semiconductors Logo 




Gesamt 16 Seiten
PCF1252-1 Datasheet, Funktion
INTEGRATED CIRCUITS
DATA SHEET
PCF1252-X family
Threshold detector and reset
generator
Product specification
Supersedes data of 1996 Jan 23
File under Integrated Circuits, IC11
1998 Apr 16






PCF1252-1 Datasheet, Funktion
Philips Semiconductors
Threshold detector and reset generator
Product specification
PCF1252-X family
handbook, full pagewidth
supply voltage
typ. = 0.6 V
Vhys
VTRIP
VDD
0V
POWF
undefined
output
RESET
(SELECT = VSS)
undefined
output
reset
tR
reset
0V
tS tR
0V
MGC917
tR = reset time (duration of reset pulse).
tS = save time (time between assertion of POWF and assertion of the reset output). This time can be used for storing of critical data and orderly system
shut-down.
Vhys = hysteresis voltage (prevents oscillation around VTRIP).
Fig.3 Timing diagram.
1998 Apr 16
6

6 Page









PCF1252-1 pdf, datenblatt
Philips Semiconductors
Threshold detector and reset generator
Product specification
PCF1252-X family
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(order code 9398 652 90011).
DIP
SOLDERING BY DIPPING OR BY WAVE
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
REPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
WAVE SOLDERING
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
1998 Apr 16
12

12 Page





SeitenGesamt 16 Seiten
PDF Download[ PCF1252-1 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
PCF1252-0Threshold detector and reset generatorNXP Semiconductors
NXP Semiconductors
PCF1252-1Threshold detector and reset generatorNXP Semiconductors
NXP Semiconductors
PCF1252-2Threshold detector and reset generatorNXP Semiconductors
NXP Semiconductors
PCF1252-3Threshold detector and reset generatorNXP Semiconductors
NXP Semiconductors
PCF1252-4Threshold detector and reset generatorNXP Semiconductors
NXP Semiconductors

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche