Datenblatt-pdf.com


P87LPC762BD Schematic ( PDF Datasheet ) - NXP Semiconductors

Teilenummer P87LPC762BD
Beschreibung Low power/ low price/ low pin count 20 pin microcontroller with 2 kbyte OTP
Hersteller NXP Semiconductors
Logo NXP Semiconductors Logo 




Gesamt 57 Seiten
P87LPC762BD Datasheet, Funktion
INTEGRATED CIRCUITS
87LPC762
Low power, low price, low pin count
(20 pin) microcontroller with 2 kbyte OTP
Preliminary data
Supersedes data of 2001 Apr 04
IC28 Data Handbook
2001 Oct 26
Philips
Semiconductors






P87LPC762BD Datasheet, Funktion
Philips Semiconductors
Low power, low price, low pin count (20 pin)
microcontroller with 2 kbyte OTP
BLOCK DIAGRAM
Preliminary data
87LPC762
ACCELERATED
80C51 CPU
CRYSTAL OR
RESONATOR
2 K BYTE
CODE EPROM
INTERNAL BUS
128 BYTE
DATA RAM
PORT 2
CONFIGURABLE I/OS
PORT 1
CONFIGURABLE I/OS
PORT 0
CONFIGURABLE I/OS
KEYPAD
INTERRUPT
CONFIGURABLE
OSCILLATOR
ON-CHIP
RC
OSCILLATOR
UART
I2C
TIMER 0, 1
WATCHDOG TIMER
AND OSCILLATOR
ANALOG
COMPARATORS
POWER MONITOR
(POWER-ON RESET,
BROWNOUT RESET)
SU01577
2001 Oct 26
3

6 Page









P87LPC762BD pdf, datenblatt
Philips Semiconductors
Low power, low price, low pin count (20 pin)
microcontroller with 2 kbyte OTP
Preliminary data
87LPC762
FUNCTIONAL DESCRIPTION
Details of 87LPC762 functions will be described in the following
sections.
Enhanced CPU
The 87LPC762 uses an enhanced 80C51 CPU which runs at twice the
speed of standard 80C51 devices. This means that the performance of
the 87LPC762 running at 5 MHz is exactly the same as that of a
standard 80C51 running at 10 MHz. A machine cycle consists of 6
oscillator cycles, and most instructions execute in 6 or 12 clocks. A
user configurable option allows restoring standard 80C51 execution
timing. In that case, a machine cycle becomes 12 oscillator cycles.
In the following sections, the term “CPU clock” is used to refer to the
clock that controls internal instruction execution. This may
sometimes be different from the externally applied clock, as in the
case where the part is configured for standard 80C51 timing by
means of the CLKR configuration bit or in the case where the clock
is divided down via the setting of the DIVM register. These features
are described in the Oscillator section.
Analog Functions
The 87LPC762 incorporates two Analog Comparators. In order to
give the best analog function performance and to minimize power
consumption, pins that are actually being used for analog functions
must have the digital outputs and the digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input
Only (high impedance) mode as described in the I/O Ports section.
Digital inputs on port 0 may be disabled through the use of the
PT0AD register. Each bit in this register corresponds to one pin of
Port 0. Setting the corresponding bit in PT0AD disables that pin’s
digital input. Port bits that have their digital inputs disabled will be
read as 0 by any instruction that accesses the port.
Analog Comparators
Two analog comparators are provided on the 87LPC762. Input and
output options allow use of the comparators in a number of different
configurations. Comparator operation is such that the output is a
logical one (which may be read in a register and/or routed to a pin)
when the positive input (one of two selectable pins) is greater than
the negative input (selectable from a pin or an internal reference
voltage). Otherwise the output is a zero. Each comparator may be
configured to cause an interrupt when the output value changes.
Comparator Configuration
Each comparator has a control register, CMP1 for comparator 1 and
CMP2 for comparator 2. The control registers are identical and are
shown in Figure 2.
The overall connections to both comparators are shown in Figure 3.
There are eight possible configurations for each comparator, as
determined by the control bits in the corresponding CMPn register:
CPn, CNn, and OEn. These configurations are shown in Figure 4.
The comparators function down to a VDD of 3.0V.
When each comparator is first enabled, the comparator output and
interrupt flag are not guaranteed to be stable for 10 microseconds.
The corresponding comparator interrupt should not be enabled
during that time, and the comparator interrupt flag must be cleared
before the interrupt is enabled in order to prevent an immediate
interrupt service.
CMPn
Address: ACh for CMP1, ADh for CMP2
Not Bit Addressable
76543210
— — CEn CPn CNn OEn COn CMFn
Reset Value: 00h
BIT SYMBOL
CMPn.7, 6
CMPn.5
CEn
CMPn.4
CPn
CMPn.3
CNn
CMPn.2
CMPn.1
CMPn.0
OEn
COn
CMFn
FUNCTION
Reserved for future use. Should not be set to 1 by user programs.
Comparator enable. When set by software, the corresponding comparator function is enabled.
Comparator output is stable 10 microseconds after CEn is first set.
Comparator positive input select. When 0, CINnA is selected as the positive comparator input. When
1, CINnB is selected as the positive comparator input.
Comparator negative input select. When 0, the comparator reference pin CMPREF is selected as
the negative comparator input. When 1, the internal comparator reference Vref is selected as the
negative comparator input.
Output enable. When 1, the comparator output is connected to the CMPn pin if the comparator is
enabled (CEn = 1). This output is asynchronous to the CPU clock.
Comparator output, synchronized to the CPU clock to allow reading by software. Cleared when the
comparator is disabled (CEn = 0).
Comparator interrupt flag. This bit is set by hardware whenever the comparator output COn changes
state. This bit will cause a hardware interrupt if enabled and of sufficient priority. Cleared by
software and when the comparator is disabled (CEn = 0).
SU01152
Figure 2. Comparator Control Registers (CMP1 and CMP2)
2001 Oct 26
9

12 Page





SeitenGesamt 57 Seiten
PDF Download[ P87LPC762BD Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
P87LPC762BDLow power/ low price/ low pin count 20 pin microcontroller with 2 kbyte OTPNXP Semiconductors
NXP Semiconductors
P87LPC762BDHLow power/ low price/ low pin count 20 pin microcontroller with 2 kbyte OTPNXP Semiconductors
NXP Semiconductors
P87LPC762BNLow power/ low price/ low pin count 20 pin microcontroller with 2 kbyte OTPNXP Semiconductors
NXP Semiconductors

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche