Datenblatt-pdf.com


EL6249CU Schematic ( PDF Datasheet ) - Elantec Semiconductor

Teilenummer EL6249CU
Beschreibung 4-Ch Laser Diode Driver Oscillator
Hersteller Elantec Semiconductor
Logo Elantec Semiconductor Logo 




Gesamt 2 Seiten
EL6249CU Datasheet, Funktion
EL6249C - Product Brief
4-Ch Laser Diode Driver + Oscillator
Features
• “Shrink-Small” Outline Package
• Voltage controlled output current
source, requiring one external set
resistor per channel
• Auto Oscillator On-Off with
OUTEN Signals
• Rise time = 0.8ns
• Fall time = 0.8ns
• On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
• Oscillator to 500MHz
• Oscillator to 100mA pk/pk
• Single +5V supply (±10%)
• Current amplification = 100
• Disable feature for power-up
protection and power savings
• CMOS control signals
Applications
• CD-RW applications
• Writable optical drives
• Laser diode current switching
Ordering Information
Part No.
EL6249CU
Temp. Range
0°C to +70°C
Package
16-Pin QSOP
Outline #
MDP0040
General Description
The EL6249C is a four channel laser diode current amplifier that pro-
vides controlled current to a grounded laser diode. Channels 2, 3, and 4
should be used as the write channels, with switching speeds of approxi-
mately one nanosecond rise/fall time. All four channels are summed
together at the IOUT output, allowing the user to create multilevel wave-
forms in order to optimize laser diode performance. The level of the
output current is set by an analog voltage applied to an external resistor
which converts the voltage into a current at the IIN pin (virtually
ground). The current seen at this pin is then amplified to become a cur-
rent source at pin IOUT.
Output current pulses are enabled when an ‘L’ signal is applied to the
OUTEN pin. No output current flows when OUTEN is ‘H’ and addi-
tional laser diode protection is provided since the OUTEN input will
float high when open. Complete IOUT shutoff is also achieved by hold-
ing the ENABLE pin low, which will override the OUTEN control pins.
An on-chip 500MHz oscillator is provided to allow output current mod-
ulation when in read mode. The oscillator is enabled when the OSCEN
pin is held high. If any of channels 2, 3, or 4 are active, the oscillator is
switched off. Complete control of amplitude and frequency is set by
two external resistors connected to ground at pins RFREQ and RAMP
(see graphs in this data sheet for further explanation).
The external IIN resistors allow the user to accurately and independently
set each amplifier transconductance by applying a voltage to each resis-
tor, without restriction on the voltage range, thus ensuring broad
voltage DAC compatibility. Alternatively, the IIN pin can be biased
from a current DAC or other current source.
Connection Diagram
1 IINR
VCC 16
2 IIN2
VCC 15
3 RFREQ
IOUT 14
4 IIN3
GND 13
5 IIN4
RAMP 12
6 OUTEN2 ENABLE 11
7 OUTEN3 OSCEN 10
8 OUTEN4
VCC 9
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.





SeitenGesamt 2 Seiten
PDF Download[ EL6249CU Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
EL6249C4-Ch Laser Diode Driver OscillatorElantec Semiconductor
Elantec Semiconductor
EL6249CU4-Ch Laser Diode Driver OscillatorElantec Semiconductor
Elantec Semiconductor

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche