Datenblatt-pdf.com


EL5197CS-T13 Schematic ( PDF Datasheet ) - Elantec Semiconductor

Teilenummer EL5197CS-T13
Beschreibung Single 200MHz Fixed Gain Amplifier
Hersteller Elantec Semiconductor
Logo Elantec Semiconductor Logo 




Gesamt 14 Seiten
EL5197CS-T13 Datasheet, Funktion
EL5197C - Preliminary
Single 200MHz Fixed Gain Amplifier
Features
• Gain selectable (+1, -1, +2)
• 200MHz -3dB BW (AV = 1, 2)
• 4mA supply current
• Single and dual supply operation,
from 5V to 10V
• Available in 5-pin SOT23 package
• Triple (EL5397C) available
• 400MHz, 9mA product available
(EL5196C, EL5396C)
Applications
• Battery Powered Equipment
• Hand Held, Portable Devices
• Video Amplifier
• Cable Drivers
• RGB Amplifier
• Test Equipment
• Instrumentation
• Current to Voltage Converters
General Description
The EL5197C is a fixed gain amplifier with a bandwidth of 200MHz,
making these amplifiers ideal for today’s high speed video and moni-
tor applications. The EL5197C features internal gain setting resistors
and can be configured in a gain of +1, -1 or +2. The same bandwidth is
seen in both gain-of-1 and gain-of-2 applications.
With a supply current of just 4mA and the ability to run from a single
supply voltage from 5V to 10V, these amplifiers are also ideal for
hand held, portable or battery powered equipment.
For applications where board space is critical, the EL5197C is offered
in the 5-pin SOT23 package, as well as an 8-pin SO. The EL5197C
operates over the industrial temperature range of -40°C to +85°C.
Ordering Information
Part No
EL5197CW-T7
EL5197CW-T13
EL5197CS
EL5197CS-T7
EL5197CS-T13
Package
5-Pin SOT23
5-Pin SOT23
8-Pin SO
8-Pin SO
8-Pin SO
Tape &
Reel
7”
13”
-
7”
13”
Outline #
MDP0038
MDP0038
MDP0027
MDP0027
MDP0027
Pin Configurations
OUT 1
VS- 2
IN+ 3
5-Pin SOT23
+-
EL5197CW
5 VS+
4 IN-
NC 1
IN- 2
IN+ 3
VS- 4
8-Pin SO
-
+
EL5197CS
8 NC*
7 VS+
6 OUT
5 NC
* This pin must be left disconnected
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.






EL5197CS-T13 Datasheet, Funktion
EL5197C - Preliminary
Single 200MHz Fixed Gain Amplifier
Typical Performance Curves
Output Voltage Swing vs Frequency
THD<1%
10
RL=500
8
RL=150
6
4
2
AV=2
0
1
10
Frequency (MHz)
100
Small Signal Step Response
VS=±5V
RL=150
AV=2
200mV/div
Output Voltage Swing vs Frequency
THD<0.1%
10
8 RL=500
6
RL=150
4
2
AV=2
0
1
10
Frequency (MHz)
Large Signal Step Response
100
VS=±5V
RL=150
AV=2
1V/div
10ns/div
Settling Time vs Settling Accuracy
25
AV=2
20
RL=150
VSTEP=5VP-P output
15
10
5
0
0.01 0.1
Settling Accuracy (%)
1
10ns/div
Transimpedance (RoI) vs Temperature
625
600
575
550
525
-40
6
10 60 110
Die Temperature (°C)
160

6 Page









EL5197CS-T13 pdf, datenblatt
EL5197C - Preliminary
Single 200MHz Fixed Gain Amplifier
stability increases. Since the loop stability is improving
with higher closed-loop gains, it becomes possible to
reduce the value of RF below the specified 475and
still retain stability, resulting in only a slight loss of
bandwidth with increased closed-loop gain.
Supply Voltage Range and Single-Supply
Operation
The EL5197C has been designed to operate with supply
voltages having a span of greater than 5V and less than
10V. In practical terms, this means that the EL5197C
will operate on dual supplies ranging from ±2.5V to
±5V. With single-supply, the EL5197C will operate
from 5V to 10V.
As supply voltages continue to decrease, it becomes nec-
essary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL5197C has an input range which extends to within 2V
of either supply. So, for example, on +5V supplies, the
EL5197C has an input range which spans ±3V. The out-
put range of the EL5197C is also quite large, extending
to within 1V of the supply rail. On a ±5V supply, the
output is therefore capable of swinging from -----4V to
+4V. Single-supply output range is larger because of the
increased negative swing due to the external pull-down
resistor to ground.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same fre-
quency response as DC levels are changed at the output.
This is especially difficult when driving a standard video
load of 150, because of the change in output current
with DC level. Previously, good differential gain could
only be achieved by running high idle currents through
the output transistors (to reduce variations in output
impedance.) These currents were typically comparable
to the entire 4mA supply current of each EL5197C
amplifier. Special circuitry has been incorporated in the
EL5197C to reduce the variation of output impedance
with current output. This results in dG and dP specifica-
tions of 0.03% and 0.04°, while driving 150at a gain
of 2.
Video performance has also been measured with a 500
load at a gain of +1. Under these conditions, the
EL5197C has dG and dP specifications of 0.03% and
0.04°.
Output Drive Capability
In spite of its low 4mA of supply current, the EL5197C
is capable of providing a minimum of ±120mA of output
current. With a minimum of ±120mA of output drive,
the EL5197C is capable of driving 50loads to both
rails, making it an excellent choice for driving isolation
transformers in telecommunications applications.
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is
always recommended for reflection-free performance.
For those applications, the back-termination series resis-
tor will decouple the EL5197C from the cable and allow
extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termina-
tion resistor. In these applications, a small series resistor
(usually between 5and 50) can be placed in series
with the output to eliminate most peaking. The gain
resistor (RG) can then be chosen to make up for any gain
loss which may be created by this additional resistor at
the output. In many cases it is also possible to simply
increase the value of the feedback resistor (RF) to reduce
the peaking.
Current Limiting
The EL5197C has no internal current-limiting circuitry.
If the output is shorted, it is possible to exceed the Abso-
lute Maximum Rating for output current or power
dissipation, potentially resulting in the destruction of the
device.
Power Dissipation
With the high output drive capability of the EL5197C, it
is possible to exceed the 150°C Absolute Maximum
junction temperature under certain very high load cur-
rent conditions. Generally speaking when RL falls below
about 25, it is important to calculate the maximum
junction temperature (TJMAX) for the application to
determine if power supply voltages, load conditions, or
package type need to be modified for the EL5197C to
12

12 Page





SeitenGesamt 14 Seiten
PDF Download[ EL5197CS-T13 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
EL5197CS-T13Single 200MHz Fixed Gain AmplifierElantec Semiconductor
Elantec Semiconductor

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche