|
|
PDF EL2186C Data sheet ( Hoja de datos )
| Número de pieza | EL2186C | |
| Descripción | 250MHz/3mA Current Mode Feedback Amp w/Disable | |
| Fabricantes | Elantec Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de EL2186C (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
|
No Preview Available !
EL2186C, EL2286C
250MHz/3mA Current Mode Feedback Amp w/Disable
Features
• Single (EL2186C) and dual
(EL2286C) topologies
• 3mA supply current (per amplifier)
• 250MHz -3dB bandwidth
• Low cost
• Fast disable
• Powers down to 0mA
• Single- and dual-supply operation
down to ±1.5V
• 0.05%/0.05° diff. gain/diff. phase
into 150Ω
• 1200V/µs slew rate
• Large output drive current:
100mA (EL2186C)
55mA (EL2286C)
• Also available without disable in
single (EL2180C), dual
(EL2280C) and quad (EL2480C)
• Lower power EL2170C/EL2176C
family also available (1 mA/
70MHz) in single, dual and quad
Applications
• Low power/battery applications
• HDSL amplifiers
• Video amplifiers
• Cable drivers
• RGB amplifiers
• Test equipment amplifiers
• Current to voltage converters
Ordering Information
Part No.
EL2186CN
EL2186CS
EL2286CN
EL2286CS
Temp. Range
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
Package
8-Pin PDIP
8-Pin SOIC
14-Pin PDIP
14-Pin SOIC
Outline #
MDP0031
MDP0027
MDP0031
MDP0027
General Description
The EL2186C/EL2286C are single/dual current-feedback operational
amplifiers which achieve a -3dB bandwidth of 250MHz at a gain of +1
while consuming only 3mA of supply current per amplifier. They will
operate with dual supplies ranging from ±1.5V to ±6V, or from single
supplies ranging from +3V to +12V. The EL2186C/EL2286C also
include a disable/power-down feature which reduces current con-
sumption to 0mA while placing the amplifier output in a high
impedance state. In spite of its low supply current, the EL2286C can
output 55mA while swinging to ±4V on ±5V supplies. The EL2186C
can output 100mA with similar output swings. These attributes make
the EL2186C/EL2286C excellent choices for low power and/or low
voltage cable-driver, HDSL, or RGB applications.
For Single, Dual and Quad applications without disable, consider the
EL2180C (8-Pin Single), EL2280C (8-Pin Dual) or EL2480C (14-Pin
Quad). For lower power applications where speed is still a concern,
consider the EL2170C/El2176C family which also comes in similar
Single, Dual and Quad configurations. The EL2170C/EL2176C fam-
ily provides a -3dB bandwidth of 70MHz while consuming 1mA of
supply current per amplifier.
Connection Diagrams
EL2186C SO, P-DIP
EL2286C SO, P-DIP
Manufactured under U.S. Patent No. 5,418,495
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.
1 page  
EL2186C, EL2286C
250MHz/3mA Current Mode Feedback Amp w/Disable
Typical Performance Curves
Non-Inverting Frequency
Response (Gain)
Non-Inverting Frequency
Response (Phase)
Frequency Response
for Various RF and RG
Inverting Frequency
Response (Gain)
Inverting Frequency
Response (Phase)
Frequency Response
for Various RL and CL
Transimpedance (ROL)
vs Frequency
PSRR and CMRR
vs Frequency
Frequency Response for
Various CIN-
5
5 Page 
EL2186C, EL2286C
250MHz/3mA Current Mode Feedback Amp w/Disable
resistors further exacerbates the problem by further low-
ering the pole frequency.
The EL2186C/EL2286C have been specially designed
to reduce power dissipation in the feedback network by
using large 750Ω feedback and gain resistors. With the
high bandwidths of these amplifiers, these large resistor
values would normally cause stability problems when
combined with parasitic capacitance, but by internally
canceling the effects of a nominal amount of parasitic
capacitance, the EL2186C/EL2286C remain very stable.
For less experienced users, this feature makes the
EL2186C/EL2286C much more forgiving, and therefore
easier to use than other products not incorporating this
proprietary circuitry.
The experienced user with a large amount of PC board
layout experience may find in rare cases that the
EL2186C/EL2286C have less bandwidth than expected.
In this case, the inverting input may have less parasitic
capacitance than expected
by the internal compensation circuitry of the
EL2186C/EL2286C. The reduction of feedback resistor
values (or the addition of a very small amount of exter-
nal capacitance at the inverting input, e.g. 0.5pF) will
increase bandwidth as desired. Please see the curves for
Frequency Response for Various RF and RG, and Fre-
quency Response for Various CIN-.
Feedback Resistor Values
The EL2186C/EL2286C have been designed and speci-
fied at gains of +1 and +2 with RF = 750Ω. This value of
feedback resistor gives 250MHz of -3dB bandwidth at
AV = +1 with about 2.5dB of peaking, and 180MHz of -
3dB bandwidth at AV = +2 with about 0.1dB of peaking.
Since the EL2186C/EL2286C are current-feedback
amplifiers, it is also possible to change the value of RF to
get more bandwidth. As seen in the curve of Frequency
Response For Various RF and RG, bandwidth and peak-
ing can be easily modified by varying the value of the
feedback resistor.
Because the EL2186C/EL2286C are current-feedback
amplifiers, their gain-bandwidth product is not a con-
stant for different closed-loop gains. This feature
actually allows the EL2186C/EL2286C to maintain
about the same -3dB bandwidth, regardless of closed-
loop gain. However, as closed-loop gain is increased,
bandwidth decreases slightly while stability increases.
Since the loop stability is improving with higher closed-
loop gains, it becomes possible to reduce the value of RF
below the specified 750Ω and still retain stability, result-
ing in only a slight loss of bandwidth with increased
closed-loop gain.
Supply Voltage Range and Single-Supply
Operation
The EL2186C/EL2286C have been designed to operate
with supply voltages having a span of greater than 3V,
and less than 12V. In practical terms, this means that the
EL2186C/EL2286C will operate on dual supplies rang-
ing from ±1.5V to ±6V. With a single-supply, the
EL2176C will operate from +3V to +12V.
As supply voltages continue to decrease, it becomes nec-
essary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL2186C/EL2286C have an input voltage range that
extends to within 1V of either supply. So, for example,
on a single +5V supply, the EL2186C/EL2286C have an
input range which spans from 1V to 4V. The output
range of the EL2186C/EL2286C is also quite large,
extending to within 1V of the supply rail. On a ±5V sup-
ply, the output is therefore capable of swinging from -
4V to +4V. Single-supply output range is even larger
because of the increased negative swing due to the exter-
nal pull-down resistor to ground. On a single +5V
supply, output voltage range is about 0.3V to 4V.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same fre-
quency response as DC levels are changed at the output.
This is especially difficult when driving a standard video
load of 150Ω, because of the change in output current
with DC level. Until the EL2186C/EL2286C, good Dif-
ferential Gain could only be achieved by running high
idle currents through the output transistors (to reduce
variations in output impedance). These currents were
typically comparable to the entire 3mA supply current of
each EL2186C/EL2286C amplifier! Special circuitry
has been incorporated in the EL2186C/EL2286C to
reduce the variation of output impedance with current
11
11 Page | ||
| Páginas | Total 19 Páginas | |
| PDF Descargar | [ Datasheet EL2186C.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| EL2186 | 250MHz/3mA Current Mode Feedback Amp w/Disable |  Intersil Corporation |
| EL2186C | 250MHz/3mA Current Mode Feedback Amp w/Disable | Elantec Semiconductor |
| EL2186CN | 250MHz/3mA Current Mode Feedback Amp w/Disable | Elantec Semiconductor |
| EL2186CN | 250MHz/3mA Current Mode Feedback Amp w/Disable | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |