Datenblatt-pdf.com


ECP203D-PCB2450 Schematic ( PDF Datasheet ) - ETC

Teilenummer ECP203D-PCB2450
Beschreibung 2 Watt/ High Linearity InGaP HBT Amplifier
Hersteller ETC
Logo ETC Logo 




Gesamt 3 Seiten
ECP203D-PCB2450 Datasheet, Funktion
ECP203
2 Watt, High Linearity InGaP HBT Amplifier
The Communications Edge TM
Product Information
Product Features
x 2300 – 2700 MHz
x +32.5 dBm P1dB
x +48 dBm Output IP3
x 10 dB Gain @ 2450 MHz
x 9 dB Gain @ 2600 MHz
x Single Positive Supply (+5V)
x Available in SOIC-8 or 16pin
4mm QFN package
Applications
x W-LAN
x RFID
x DMB
x Fixed Wireless
Product Description
The ECP203 is a high dynamic range driver amplifier in
a low-cost surface mount package. The InGaP/GaAs
HBT is able to achieve high performance for various
narrowband-tuned application circuits with up to +48
dBm OIP3 and +32.5 dBm of compressed 1dB power. It
is housed in an industry standard SOIC-8 or 16-pin
4x4mm QFN SMT package. All devices are 100% RF
and DC tested.
The ECP203 is targeted for use as a driver amplifier in
wireless infrastructure where high linearity and medium
power is required. An internal active bias allows the
ECP203 to maintain high linearity over temperature and
operate directly off a single +5V supply. This
combination makes the device an excellent candidate for
driver amplifier stages in wireless-LAN, digital
multimedia broadcast, or fixed wireless applications. The
device can also be used in next generation RFID readers.
Functional Diagram
Vref 1
N/C 2
RF IN 3
N/C 4
16 15 14
567
13
12 N/C
11 RF OUT
10 RF OUT
9 N/C
8
ECP203D
Vref 1
N/C 2
RF IN 3
N/C 4
8 Vbias
7 RF OUT
6 RF OUT
ECP203G
5 N/C
Specifications (1)
Parameter
Units
Operational Bandwidth
MHz
Test Frequency
MHz
Gain dB
Input Return Loss
dB
Output Return Loss
dB
Output P1dB
dBm
Output IP3 (2)
dBm
Noise Figure
dB
Test Frequency
MHz
Gain dB
Output P1dB
dBm
Output IP3 (2)
dBm
Operating Current Range, Icc (3) mA
Device Voltage, Vcc
V
Min
2300
700
Typ
2450
10
20
6.8
+32.5
+48
7.7
2600
9
+32
+47
800
+5
Max
2700
900
1. Test conditions unless otherwise noted: 25ºC, Vsupply = +5 V in tuned application circuit.
2. 3OIP measured with two tones at an output power of +17 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
3. This corresponds to the quiescent current or operating current under small-signal conditions into pins 6, 7, and 8. It is expected that the current can increase by an additional 200 mA at P1dB. Pin 1 is used as
a reference voltage for the internal biasing circuitry. It is expected that Pin 1 will pull 22mA of current when used with a series bias resistor of R1=15¡ . (ie. total device current typically will be 822 mA.)
Absolute Maximum Rating
Ordering Information
Parameters
Operating Case Temperature
Storage Temperature
RF Input Power (continuous)
Device Voltage
Device Current
Device Power
Rating
-40 to +85 qC
-65 to +150 qC
+28 dBm
+8 V
1400 mA
8W
Part No.
ECP203D
ECP203G
ECP203D-PCB2450
ECP203D-PCB2650
ECP203G-PCB2450
ECP203G-PCB2650
Description
2 Watt InGaP HBT Amplifier (16p 4mm Pkg)
2 Watt InGaP HBT Amplifier (Soic-8 Pkg)
2450 MHz Evaluation Board
2600 MHz Evaluation Board
2450 MHz Evaluation Board
2600 MHz Evaluation Board
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc   Phone 1-800-WJ1-4401   FAX: 408-577-6621   e-mail: [email protected]   Web site: www.wj.com
OCtober 2004





SeitenGesamt 3 Seiten
PDF Download[ ECP203D-PCB2450 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
ECP203D-PCB24502 Watt/ High Linearity InGaP HBT AmplifierETC
ETC

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche