|
|
PDF A3189UA Data sheet ( Hoja de datos )
| Número de pieza | A3189UA | |
| Descripción | HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | |
| Fabricantes | Allegro MicroSystems | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de A3189UA (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
3185 THRU
3189
HALL-EFFECT LATCHES
FOR HIGH-TEMPERATURE OPERATION
V
CC
12
3
Dwg. PH-003A
Pinning is shown viewed from branded side.
These Hall-effect latches are extremely temperature-stable and stress-
resistant sensors especially suited for operation over extended temperature
ranges to +150°C. Superior high-temperature performance is made possible
through a novel Schmitt trigger circuit that maintains operate and release
point symmetry by compensating for temperature changes in the Hall ele-
ment. Additionally, internal compensation provides magnetic switch points
that become more sensitive with temperature, hence offsetting the usual
degradation of the magnetic field with temperature. The symmetry capability
makes these devices ideal for use in pulse-counting applications where duty
cycle is an important parameter. The four basic devices (3185, 3187, 3188,
and 3189) are identical except for magnetic switch points.
Each device includes on a single silicon chip a voltage regulator, qua-
dratic Hall-voltage generator, temperature compensation circuit, signal
amplifier, Schmitt trigger, and a buffered open-collector output to sink up to
25 mA. The on-board regulator permits operation with supply voltages of 3.8
to 24 volts.
The first character of the part number suffix determines the device
operating temperature range. Suffix ‘E–’ is for -40°C to +85°C, and suffix
‘L–’ is for -40°C to +150°C. Three package styles provide a magnetically
optimized package for most applications. Suffix ‘–LT’ is a miniature SOT-
89/TO-243AA transistor package for surface-mount applications; suffix ‘–U’
is a three-lead plastic mini-SIP, while suffix ‘–UA’ is a three-lead ultra-mini-
SIP.
ABSOLUTE MAXIMUM RATINGS
at TA = +25°C
Supply Voltage, VCC ............................ 30 V
Reverse Battery Voltage, VRCC ........... -30 V
Magnetic Flux Density, B ........... Unlimited
Output OFF Voltage, VOUT .................. 30 V
Reverse Output Voltage, VOUT .......... -0.5 V
Continuous Output Current, IOUT ..... 25 mA
Operating Temperature Range, TA
Suffix ‘E–’ ................... -40°C to +85°C
Suffix ‘L–’ ................. -40°C to +150°C
Storage Temperature Range,
TS ............................... -65°C to +170°C
FEATURES
I Symmetrical Switch Points
I Superior Temperature Stability
I Operation From Unregulated Supply
I Open-Collector 25 mA Output
I Reverse Battery Protection
I Activate With Small, Commercially Available Permanent Magnets
I Solid-State Reliability
I Small Size
I Resistant to Physical Stress
Always order by complete part number: the prefix ‘A’ + the basic four-digit
part number + a suffix to indicate operating temperature range +
a suffix to indicate package style, e.g., A3185ELT .
1 page  
3185 THRU 3189
HALL-EFFECT LATCHES
FOR HIGH-TEMPERATURE
OPERATION
PACKAGE DESIGNATOR ‘U’
Dimensions in Inches
(controlling dimensions)
Dimensions in Millimeters
(for reference only)
0.183
0.178
0.063
0.059
4.65
4.52
1.60
1.50
0.181
0.176
0.086 1 2 3
MAX
0.600
0.560
SEE NOTE
0.016
45°
0.018
0.015
0.050
0.100
Dwg. MH-003D in
4.60
4.47
2.18
MAX
1
15.24
14.23
SEE NOTE
23
0.41
45°
0.46
0.38
1.27
2.54
Dwg. MH-003D mm
Devices in the ‘U’ package are
NOT RECOMMENDED FOR NEW DESIGN
NOTES: 1.
2.
3.
4.
5.
6.
Tolerances on package height and width represent allowable mold offsets. Dimensions given are
measured at the widest point (parting line).
Exact body and lead configuration at vendor’s option within limits shown.
Height does not include mold gate flash.
Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm).
Where no tolerance is specified, dimension is nominal.
Minimum lead length was 0.500" (12.70 mm). If existing product to the original specifications is not acceptable,
contact sales office before ordering.
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet A3189UA.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| A3189U | HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | Allegro MicroSystems |
| A3189UA | HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | Allegro MicroSystems |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |