|
|
Teilenummer | ADM8513 |
|
Beschreibung | USB TO 10/100 MBPS ETHERNET LAN CONTROLLER | |
Hersteller | ETC | |
Logo | ||
Gesamt 30 Seiten Feature
!
+**"1#
!"
!
"
#
"
!
1&"
&*
.&.
"
"
4
5
1&"67
&*%8
7
"
&
*
)
!"
#
"
$
"#%&
#!
"
#
"
"
"
&"
"
#
" '
"
!"
1&"
9(/
1'06
,
""&%.&"%
1'06
!"
!
,*
'6
(")"*
:+,
,*
+,
-.+
- "
'6
*
/(+,
-.+
-0#
"*
/(+,
-
"
"*
+,
-
!"
7%
"
7%)""
6+
6+
!"
!
*123+,
!
""
7%)-"
7%)
"
"
+
! "
!#$#%&'&
(&
)
*
& +
,,'&*# &- #./
$"
HOST Interface
Name
I/O Description
CLK48_I
16
I 48Mhz Clock Input from crystal or oscillator.
CLK48_O 15
O Output for crystal.
RST#
14
I External Hardware Reset Input, schmitt trigger, internal pull
high
DM 20
I/O USB Data Minus pin.
DP 19
Physical Interface
I/O USB Data Plus pin.
RXIP, RXIN 36,35
I Rx input
TXOP, TXON 46,47
O Tx Out
CLK25_I
44
I Crystal In, 25Mhz
CLK25_O 43
O Crystal Out, 25Mhz
RIBB 41
I Reference Bias Resistor, tied to external 10K(1%) resistor to
ground
TSTA, TSTB 38,39
LED Interface
O Test Output Pin
LED0
33
O
LED display for 100M b/s or 10M b/s speed. Active low indicates
100Base-TX, active high indicates 10 BaseT.
LED1
32
O
LED display for link and activity status. Active low when link is
established.
LED2
31
O
LED display for Full Duplex or Collision status. Active low
indicates full duplex, high indicates collision in half duplex.
Note:
The LED interface is EEPROM-programmable, 2 bit EEPROM control bit, Address 0B[7:6] at EEPROM,
is used to select LED mode, the default setting are:
(1) LED0: 100Mbps(on, drive ‘0’) or 10Mbps(off, drive ‘1’)
(2) LED1: link (keeps on when link ok) or activity (blink with 10Hz when Pegasus II is receiving or
transmitting but not collision)
(3) LED2: full duplex (keeps on when in full duplex mode) or collision (blink with 20Hz when
colliding)
(4) All LED pins will be tri-state when using external PHY (offset 81h with bit[4:2] = 3’b001)
Mapping between LED action and EEPROM 0B[7:6] setting:
EEPROM 0B [7:6] LED
Action
LED0 10/100(OFF/ON)
0,0 LED1 LINK/ACTIVITY (ON / Flash)
LED2 FULL DUP/COL (ON / Flash)
LED0 ACTIVITY when LINK (Flash)
0,1 LED1 LINK 10(ON)
LED2 LINK 100(ON
EEPROM Interface
+
! "
!#$#%&'&
(&
)
*
& +
,,'&*# &- #./
6 Page !" *,'( )$
!
)&
!&
'> (>
4 *
&
&
*
, *
;
&0
5> ,!
?7@4 *
&0
&
+=(94 0
!" *'(" -$..
!
)&
!&
;
, 4-
;
'> (>
4 *
&
&
*
5> A,! &4&
&4&
4
0&
&2
+=(94 0
&
*0:
&0
D*
&4&
#
+=(94 0
&
*
0
& 1
:1'>
5> ,
9 :
*
4 0
0&&:
&
*0:
!" *'( ".
!
)&
!&
'> (>
4 *
&
&
*
"&E
5> A,! &4&
&4&
F:1
4
0&
&2
+=(94 0
&
!!.&*&
D*
&4&
#
+=(94 0
&
*
0
& 1
:1'>
4
&4&
G#
&
!!.&*&
0
D*
F:1
#
+=(94 0
&
0&
, 4-
;"&E
5> ,
9 :
*
4 0
0&&:
*&
&
!!.&E
!" *'(*
)&
!&
'>
;
,;
(>
5>
4 0
;&
;
&
5>
4 *
&
&
*
,
:
9+
:1
,,-
0
4 0
;&
A$F&
&
,& :
9+
:1
,,4*
&
A:,, & *
&
&
44 0
&
#&
&40
,0
0
A:,,40
,*4 0
;&
0$F#9+
:1
,,
A:,40
*4 0
;&
0$F#9+
:1
,,
A:40
*4 0
;&
0$F#9+
:1
,,
+
! "
!#$#%&'&
(&
)
*
& +
,,'&*# &- #./
12 Page | ||
Seiten | Gesamt 30 Seiten | |
PDF Download | [ ADM8513 Schematic.PDF ] |
Teilenummer | Beschreibung | Hersteller |
ADM8513 | USB TO 10/100 MBPS ETHERNET LAN CONTROLLER | ETC |
Teilenummer | Beschreibung | Hersteller |
CD40175BC | Hex D-Type Flip-Flop / Quad D-Type Flip-Flop. |
Fairchild Semiconductor |
KTD1146 | EPITAXIAL PLANAR NPN TRANSISTOR. |
KEC |
www.Datenblatt-PDF.com | 2020 | Kontakt | Suche |