Datenblatt-pdf.com


GS81302S18E Schematic ( PDF Datasheet ) - GSI Technology

Teilenummer GS81302S18E
Beschreibung 144Mb SigmaSIO DDR -II Burst of 2 SRAM
Hersteller GSI Technology
Logo GSI Technology Logo 




Gesamt 30 Seiten
GS81302S18E Datasheet, Funktion
GS81302S08/09/18/36E-375/350/333/300/250
165-Bump BGA
Commercial Temp
Industrial Temp
144Mb SigmaSIOTM DDR -II
Burst of 2 SRAM
375 MHz–250 MHz
1.8 V VDD
1.8 V and 1.5 V I/O
Features
• Simultaneous Read and Write SigmaSIO™ Interface
• JEDEC-standard pinout and package
• Dual Double Data Rate interface
• Byte Write controls sampled at data-in time
• DLL circuitry for wide output data valid window and future
frequency scaling
• Burst of 2 Read and Write
• 1.8 V +100/–100 mV core power supply
• 1.5 V or 1.8 V HSTL Interface
• Pipelined read operation
• Fully coherent read and write pipelines
• ZQ mode pin for programmable output drive strength
• IEEE 1149.1 JTAG-compliant Boundary Scan
• 165-bump, 15 mm x 17 mm, 1 mm bump pitch BGA package
• RoHS-compliant 165-bump BGA package available
SigmaSIOFamily Overview
GS81302S08/09/18/36 are built in compliance with the
SigmaSIO DDR-II SRAM pinout standard for Separate I/O
synchronous SRAMs. They are 150,994,944-bit (144Mb)
SRAMs. These are the first in a family of wide, very low
voltage HSTL I/O SRAMs designed to operate at the speeds
needed to implement economical high performance
networking systems.
Clocking and Addressing Schemes
A Burst of 2 SigmaSIO DDR-II SRAM is a synchronous
device. It employs dual input register clock inputs, K and K.
The device also allows the user to manipulate the output
register clock input quasi independently with dual output
register clock inputs, C and C. If the C clocks are tied high, the
Bottom View
165-Bump, 15 mm x 17 mm BGA
1 mm Bump Pitch, 11 x 15 Bump Array
JEDEC Std. MO-216, Variation CAB-1
K clocks are routed internally to fire the output registers
instead. Each Burst of 2 SigmaSIO DDR-II SRAM also
supplies Echo Clock outputs, CQ and CQ, which are
synchronized with read data output. When used in a source
synchronous clocking scheme, the Echo Clock outputs can be
used to fire input registers at the data’s destination.
Each internal read and write operation in a SigmaSIO DDR-II
B2 RAM is two times wider than the device I/O bus. An input
data bus de-multiplexer is used to accumulate incoming data
before it is simultaneously written to the memory array. An
output data multiplexer is used to capture the data produced
from a single memory array read and then route it to the
appropriate output drivers as needed. Therefore, the address
field of a SigmaSIO DDR-II B2 is always one address pin less
than the advertised index depth (e.g., the 16M x 8 has an 8M
addressable index).
Parameter Synopsis
tKHKH
tKHQV
-375
2.66 ns
0.45 ns
-350
2.86 ns
0.45 ns
-333
3.0 ns
0.45 ns
-300
3.3 ns
0.45 ns
-250
4.0 ns
0.45 ns
Rev: 1.03b 12/2011
1/35
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology






GS81302S18E Datasheet, Funktion
GS81302S08/09/18/36E-375/350/333/300/250
Pin Description Table
Symbol
Description
Type Comments
SA
Synchronous Address Inputs
Input —
R/W
Read/Write Contol Pin
Input Write Active Low; Read Active High
NW0–NW1
Synchronous Nybble Writes
Input
Active Low
x08 Version
BW0–BW1
Synchronous Byte Writes
Input
Active Low
x18 Version
BW0–BW3
Synchronous Byte Writes
Input
Active Low
x36 Version
K
Input Clock
Input Active High
C
Output Clock
Input Active High
TMS
Test Mode Select
Input —
TDI
Test Data Input
Input —
TCK
Test Clock Input
Input —
TDO
Test Data Output
Output
VREF
HSTL Input Reference Voltage
Input —
ZQ
Output Impedance Matching Input
Input
K
Input Clock
Input Active Low
C
Output Clock
Output
Active Low
DOFF
DLL Disable
— Active Low
LD
Synchronous Load Pin
— Active Low
CQ
Output Echo Clock
Output
Active Low
CQ
Output Echo Clock
Output
Active High
Dn
Synchronous Data Inputs
Input —
Qn
Synchronous Data Outputs
Output
VDD
Power Supply
Supply
1.8 V Nominal
VDDQ
Isolated Output Buffer Supply
Supply
1.8 or 1.5 V Nominal
VSS
Power Supply: Ground
Supply
NC
No Connect
——
Notes:
1. C, C, K, or K cannot be set to VREF voltage.
2. When ZQ pin is directly connected to VDDQ, output impedance is set to minimum value and it cannot be connected to ground or left
unconnected.
3. NC = Not Connected to die or any other pin
Rev: 1.03b 12/2011
6/35
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology

6 Page









GS81302S18E pdf, datenblatt
GS81302S08/09/18/36E-375/350/333/300/250
B2 Byte Write Clock Truth Table
BW BW
Current Operation
K
(tn + 1)
K
(tn + 1½)
K
(tn)
TT
Write
Dx stored if BWn = 0 in both data transfers
TF
Write
Dx stored if BWn = 0 in 1st data transfer only
FT
Write
Dx stored if BWn = 0 in 2nd data transfer only
FF
Write Abort
No Dx stored in either data transfer
Notes:
1. “1” = input “high”; “0” = input “low”; “X” = input “don’t care”; “T” = input “true”; “F” = input “false”.
2. If one or more BWn = 0, then BW = “T”, else BW = “F”.
D
K
(tn + 1)
D1
D1
X
X
D
K
(tn + 1½)
D2
X
D2
X
Rev: 1.03b 12/2011
12/35
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology

12 Page





SeitenGesamt 30 Seiten
PDF Download[ GS81302S18E Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
GS81302S18E144Mb SigmaSIO DDR -II Burst of 2 SRAMGSI Technology
GSI Technology
GS81302S18GE144Mb SigmaSIO DDR -II Burst of 2 SRAMGSI Technology
GSI Technology

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche