|
|
PDF PML18 Data sheet ( Hoja de datos )
| Número de pieza | PML18 | |
| Descripción | Ultra-low Ohmic Chip Resistors | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PML18 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
Ultra-low Ohmic Chip Resistors for Current Detection <Wide Terminal type>
PML Series
Datasheet
Features
1) Ultra low-ohmic resistance range.
2) Wide terminal configuration for high joint reliability.
3) Improved current detection accuracy by trimming-less structure.
4) ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.
Products List
Part No.
Size
(mm) (inch)
Rated Power
(70°C)
(W)
Temperature
Coefficient
(ppm / °C)
PML10
1220 0508
0.66
±200
Resistance
Tolerance
(%)
J(±5%)
G(±2%)
PML18
1632 0612
1
±150
J(±5%)
G(±2%)
Resistance Range
(mΩ)
1.0, 1.5, 2.0, 2.5
0.5, 1.0, 1.5, 2.0, 2.5
PML50
1.5
2550 1020 (2W at 25°C)
±200
J(±5%)
0.5, 1.0, 1.5, 2.0, 2.2
PML100
3264
1225
2
(3W at 25°C)
2
±100
±150
J(±5%)
1.0, 1.5, 2.0, 2.2
0.5
: Under development
∗Design and specifications are subject to change without notice.
Carefully check the specification sheet supplied with the product before using or ordering it.
Operating
Temperature
Range
(°C)
Automotive
Grade
Available
(AEC-Q200)
−55 to +155
Yes
Part Number Description
PML
10
EZP
J V 1L0
Part No.
PML
(Ultra-low Ohmic
Chip Resistors
for Current Detection
/ Wide terminal type)
Size (mm [inch])
10 (1220 [0508])
18 (1632 [0612])
50 (2550 [1020])
100 (3264 [1225])
Packaging Specifications Code
Part No.
Code
Packaging Quantity
specifications / Reel
PML10 EZP
Paper tape
(4mm Pitch)
5,000
PML18 EZP
Paper tape
(4mm Pitch)
5,000
PML50 HZP
Embossed tape
(4mm Pitch)
2,000
PML100 HZP
Embossed tape
(4mm Pitch)
2,000
Resistance
Tolerance
G ( ±2% )
J ( ±5% )
Special
part code
Nominal Resistance
Resistance code,
3 or 4 digits.
Resistance Resistance Tolerance
Value(Ω) J
G
0.5mΩ 0L5 0L50
1mΩ 1L0 1L00
1.5mΩ 1L5 1L50
2mΩ 2L0 2L00
2.2mΩ 2L2
−
2.5mΩ 2L5 2L50
www.rohm.com
○c 2015 ROHM Co., Ltd. All rights reserved.
1/4
2015.11 - Rev.E
1 page  
Datasheet
Notice
Precaution on using ROHM Products
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU CHINA
CLASSⅢ
CLASSⅣ
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.001
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet PML18.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PML10 | Ultra-low Ohmic Chip Resistors | ROHM Semiconductor |
| PML100 | Ultra-low Ohmic Chip Resistors | ROHM Semiconductor |
| PML18 | Ultra-low Ohmic Chip Resistors | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |